Toyota Venza: Brake Control / Dynamic Control Systems
- Brake Actuator
- Brake Pedal Load Sensing Switch
- Front Speed Sensor
- Rear Speed Sensor(for 2wd)
- Rear Speed Sensor(for Awd)
- Relay
- Steering Angle Sensor
- Vehicle Stability Control System
- Precaution
- Parts Location
- System Description
- System Diagram
- How To Proceed With Troubleshooting
- Calibration
- Check For Intermittent Problems
- Test Mode Procedure
- Problem Symptoms Table
- Terminals Of Ecu
- Diagnosis System
- Dtc Check / Clear
- Freeze Frame Data
- Fail-safe Chart
- Data List / Active Test
- Diagnostic Trouble Code Chart
- Steering Angle Sensor Initialization Incomplete (C1439/31,C1445/31)
- Performance Decline of Brake Function (C1441)
- Yaw Rate Sensor Output Malfunction (C1448/98)
- Control Module Communication Bus OFF (U0073/94,U0100/65,U0123/62,U0124/95,U0126/63)
- Stop Light Control Relay Malfunction (C1380/64)
- Skid Control ECU Malfunction (C1300/62)
- Brake Pedal Load Sensing Switch (C1267/67)
- ECU Version Miss Match (C1288/88)
- Open in Stop Light Switch Circuit (C1249/49)
- Master Cylinder Pressure Sensor Malfunction (C1246/46,C1281/81)
- Speed Sensor Rotor Faulty (C1237/37,C1275/75-C1278/78)
- Low Battery Positive Voltage or Abnormally High Battery Positive Voltage (C1241/41)
- Steering Angle Sensor Circuit Malfunction (C1231/31)
- Malfunction in Deceleration Sensor (C0365/28,C1234/34,C1245/32,C1245/45)
- Engine Control System Malfunction (C1201/51)
- Open or Short Circuit in ABS Solenoid Relay Circuit (C0278/11)
- Open or Short Circuit in ABS Motor Relay Circuit (C0273/13)
- SFR Solenoid Circuit (C0226/21,C0236/22,C0246/23,C0256/24,C1225/25-C1228/28)
- ABS Control System Malfunction (43)
- Rear Speed Sensor RH Circuit (C0210/33,C0215/34,C1273/73,C1274/74,C1332/38,C1333/39)
- Front Speed Sensor RH Circuit (C0200/31,C0205/32,C1271/71,C1272/72,C1330/35,C1331/36)
- ABS Warning Light Remains ON
- ABS Warning Light does not Come ON
- Brake Warning Light Remains ON
- Brake Warning Light does not Come ON
- TRAC OFF Indicator Light Remains ON
- TRAC OFF Indicator Light does not Come ON
- VSC OFF Indicator Light Remains ON
- VSC OFF Indicator Light does not Come ON
- Slip Indicator Light does not Come ON
- Slip Indicator Light Remains ON
- TC and CG Terminal Circuit
- TS and CG Terminal Circuit
- Vsc Off Switch
- Yaw Rate And Acceleration Sensor
Rear Brake Flexible Hose
Components
COMPONENTS
ILLUSTRATION
Removal
REMOVAL
CAUTION / NOTICE / HINT
NOTICE:
If both the left and right side hoses are removed at the same time, be sure to
place identification ma ...
Brake Actuator
...
Other materials about Toyota Venza:
If the engine will not start
If the engine still does not start after following the correct starting procedure
(, 175) or releasing the steering lock (, 176), confirm the following points.
- The engine will not start even if you are carrying the correct key.
One of the followi ...
Installation
INSTALLATION
PROCEDURE
1. TEMPORARILY INSTALL SLIDING ROOF HOUSING ASSEMBLY
(a) Temporarily install the sliding roof housing panel with the 18 nuts.
NOTICE:
When installing the housing to the vehicle, first install the housing
center front and ...
Inspection
INSPECTION
PROCEDURE
1. INSPECT STARTER ASSEMBLY
NOTICE:
These tests must be performed within 3 to 5 seconds to avoid burning out the
coil.
(a) Perform a pull-in test.
(1) Remove the nut and disconnect the lead wire from terminal C.
(2) Con ...
0.1499