Toyota Venza: Automatic Transaxle System
- Definition Of Terms
- Precaution
- Parts Location
- System Description
- System Diagram
- How To Proceed With Troubleshooting
- Mechanical System Tests
- Road Test
- Hydraulic Test
- Manual Shifting Test
- Registration
- Initialization
- Monitor Drive Pattern
- Problem Symptoms Table
- Diagnosis System
- Terminals Of Ecu
- Dtc Check / Clear
- Check Mode Procedure
- Fail-safe Chart
- Data List / Active Test
- Diagnostic Trouble Code Chart
- Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL) (P2769,P2770)
- Pressure Control Solenoid "G" Performance (Shift Solenoid Valve SL4) (P2808)
- Pressure Control Solenoid "G" Electrical (Shift Solenoid Valve SL4) (P2810)
- Lost Communication with ECM / PCM "A" (U0100)
- Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU) (P2759)
- Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) (P2716)
- Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) (P2757)
- Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) (P2714)
- Pressure Control Solenoid "C" Electrical (Shift Solenoid Valve SL3) (P0798)
- Transmission Fluid Pressure Sensor / Switch "E" Circuit Low (P0989,P0990)
- Pressure Control Solenoid "C" Performance (Shift Solenoid Valve SL3) (P0796)
- Intermediate Shaft Speed Sensor "A" Circuit (P0791,P0793)
- Pressure Control Solenoid "B" Performance (Shift Solenoid Valve SL2) (P0776)
- Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2) (P0778)
- Pressure Control Solenoid "A" Electrical (Shift Solenoid Valve SL1) (P0748)
- Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1) (P0746)
- Brake Switch "B" Circuit High (P0724)
- Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL) (P0741)
- Input / Turbine Speed Sensor Circuit Malfunction (P0715,P0717)
- Transmission Fluid Temperature Sensor "A" Performance (P0711)
- Transmission Fluid Temperature Sensor "A" Circuit Low Input (P0712,P0713)
- Transmission Range Sensor Circuit Malfunction (PRNDL Input) (P0705)
- Internal Control Module EEPROM Error (P062F)
- Vehicle Speed Sensor "A" (P0500)
- Starter Relay Circuit High (P0617)
- System Voltage (P0560)
- Transmission Control Switch Circuit
- ECU Power Source Circuit
High Temperature Adjustment
HIGH TEMPERATURE ADJUSTMENT
PROCEDURE
1. ADJUST FLUID LEVEL AT HIGH TEMPERATURE
CAUTION:
Use caution while the engine is idling and the cooling fan is operating.
Be careful not to b ...
Definition Of Terms
DEFINITION OF TERMS
Term
Definition
Monitor description
Description of what the TCM monitors and how it detects malfunctions
(monitoring purpose ...
Other materials about Toyota Venza:
Starter Relay Circuit High (P0617)
MONITOR DESCRIPTION
While the engine is being cranked, battery voltage is applied to terminal STA
of the ECM. If the ECM detects the Starter Control (STA) signal while the vehicle
is being driven, it determines that there is a malfunction in the STA circu ...
Installation
INSTALLATION
PROCEDURE
1. INSTALL UNLOCK WARNING SWITCH
(a) Engage the 2 claws and install the unlock warning switch to the steering
column upper bracket.
(b) Extract the key.
(c) Co ...
Transfer Case Front Oil Seal(when Not Using The Engine Support Bridge)
Components
COMPONENTS
ILLUSTRATION
Replacement
REPLACEMENT
PROCEDURE
1. REMOVE TRANSFER ASSEMBLY
(See page ).
2. REMOVE TRANSFER CASE FRONT OIL SEAL
(a) Using SST, remove the transfer case front oil seal from the transfer
case.
...
0.1484