Toyota Venza: Internal Control Module A/D Processing Performance (P060B)

Toyota Venza Service Manual / 1ar-fe Engine Control / Sfi System / Internal Control Module A/D Processing Performance (P060B)

MONITOR DESCRIPTION

This DTC is stored when a communication error occurs in the ECM.

DTC Code	DTC Detection Condition	Trouble Area
P060B	There is an ECM main CPU communication error (1 trip detection logic)	ECM Knock control sensor

MONITOR STRATEGY

Related DTCs	P060B: Internal Control Module A/D Processing Performance
Required Sensors/Components (Main)	ECM
Required Sensors/Components (Related)	-
Frequency of Operation	Continuous
Duration	2 times: Case 1 30 time: Case 2 and 3
MIL Operation	Immediate
Sequence of Operation	None

TYPICAL ENABLING CONDITIONS

Case 1 and 2

Monitor runs whenever the following DTCs are not stored

None

Case 3

Monitor runs whenever the following DTCs are not stored	None
Both of the following conditions are met	-
Battery voltage	8 V or higher
Starter	OFF

TYPICAL MALFUNCTION THRESHOLDS

Case 1

AD converter

Fail

Case 2

Knock sensor circuit

Fail

Case 3

Knock sensor serial communication

Fail

CONFIRMATION DRIVING PATTERN

Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the Techstream off.
Turn the ignition switch off.
Disconnect the Techstream.
Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
Connect the cable to the negative (-) battery terminal.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Wait 16 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P060B.

Check the DTC judgment result.

Techstream Display	Description
NORMAL	DTC judgment completed System normal
ABNORMAL	DTC judgment completed System abnormal
INCOMPLETE	DTC judgment not completed Perform driving pattern after confirming DTC enabling conditions
N/A	Unable to perform DTC judgment Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

HINT:

If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.

If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (See page ).
HINT:
- If a permanent DTC is output, the system is malfunctioning.
- If no permanent DTC is output, the system is normal.

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.	READ OUTPUT DTC (DTC P060B)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Clear the DTC (See page ).

(e) Turn the ignition switch off and turn the Techstream off.

(f) Disconnect the Techstream.

(g) Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

(h) Connect the cable to the battery negative (-) battery terminal.

(i) Connect the Techstream to the DLC3.

(j) Turn the ignition switch to ON.

(k) Turn the Techstream on.

(l) Wait 16 seconds or more.

(m) Enter the following menus: Powertrain / Engine / Trouble Codes.

(n) Read the DTCs.

Result	Proceed to
DTC is not output	A
DTC P060B is output	B
DTC P060B and P0327, P0328 are output	C

CHECK FOR INTERMITTENT PROBLEMS

REPLACE ECM

GO TO DTC (P0327, P0328)

Internal Control Module Monitoring Processor Performance (P060A)

MONITOR DESCRIPTION The main CPU and sub CPU of the ECM perform data communication between each other. The main CPU monitors the communications and WDC pulses from the sub CPU. When the signal ma ...

Internal Control Module Accelerator Pedal Position Performance (P060D)

MONITOR DESCRIPTION The ECM monitors the input signals of the accelerator pedal position sensor No. 1. When the input signals and control signals are deviated, the DTC is stored. DTC No ...

Other materials about Toyota Venza:

Back Door cannot be Opened
DESCRIPTION When the back door cannot be opened, one of the following may be malfunctioning: 1) power back door ECU (power back door motor unit)*1 or back door closer ECU (multiplex network door ECU)*2, 2) back door lock assembly, 3) back door opener swit ...

Installation
INSTALLATION PROCEDURE 1. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY (a) Install the bush. (b) Install the lumbar support adjuster assembly with the guide and 2 screws. ...

Trailer Tongue Weight
• A recommended tongue weight varies in accordance with the types of trailers or towing as described below. • To ensure the recommended values shown below, the trailer must be loaded by referring to the following instructions. • Tongue Weight The g ...