Toyota Venza: System Description
SYSTEM DESCRIPTION
1. ACCESSORY METER ASSEMBLY
(a) Warning or Indicator
|
Item |
Detail |
|---|---|
|
Front passenger side seat belt warning light |
Receives a front passenger side seat belt warning light signal from the combination meter assembly. (Direct Line) |
|
Tire pressure warning light |
Receives a tire pressure warning light signal from the combination meter assembly. (Direct Line) |
|
AWD warning light*1 |
Receives an AWD warning light signal from the combination meter assembly. (Direct Line) |
|
Slip indicator light |
Receives a slip indicator light signal from the combination meter assembly. (Direct Line) |
|
VSC OFF indicator light |
Receives a VSC OFF indicator light signal from the combination meter assembly. (Direct Line) |
|
EPS warning light |
Receives an EPS warning light signal from the combination meter assembly. (Direct Line) |
|
Washer level warning light |
Receives a washer level warning light signal from the combination meter assembly. (Direct Line) |
|
TRAC OFF indicator light |
Receives a TRAC OFF indicator light signal from the combination meter assembly. (Direct Line) |
|
Security indicator light |
Receives a security indicator light signal from the transponder key amplifier*2 or certification ECU (smart key ECU assembly)*3. (Direct Line) |
|
Key indicator light*3 |
Receives a key indicator light signal from the combination meter assembly. (Direct Line) |
|
Passenger airbag ON/OFF indicator light |
Receives a passenger airbag ON/OFF indicator light signal from the center airbag sensor assembly. (Direct Line) |
|
MIL (Check engine warning light) |
Receives a MIL (check engine warning light) signal from the ECM. (Direct Line) |
- *1: for AWD
- *2: w/o Smart Key System
- *3: w/ Smart Key System
(b) Multi-information Display
|
Item |
Detail |
|
|---|---|---|
|
Cruise information display |
Total driving distance*1 |
Six types of information (total driving distance*1, average fuel consumption, average vehicle speed, driving time*2, current fuel consumption, and driving range) can be displayed. |
|
Average fuel consumption |
||
|
Average vehicle speed |
||
|
Driving time*2 |
||
|
Current fuel consumption |
||
|
Driving range |
||
|
Multi-information display*2 |
Each system warning |
Interrupts the multi-information display immediately when a warning occurs. |
|
DTC (Diagnostic Trouble Code) display |
Displays 2 digit DTCs pertaining to the VSC function. |
|
|
Custom setting display |
Displays the customized setting of each item. |
|
|
Outside temperature |
Displays the outside temperature. |
|
|
Adjustment display |
Press US/M M*1 or SETUP*2 switch in the drive monitor switch to enter the clock adjustment and display adjustment modes. |
|
|
Illumination control |
Displays the current illumination level and adjust the combination meter assembly brightness. |
|
|
ODO/TRIP meter |
Indicates the driving distance. |
|
- *1: w/o Multi-information Display
- *2: w/ Multi-information Display
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
Use the following procedure to troubleshoot.
PROCEDURE
1.
VEHICLE BROUGHT TO WORKSHOP
NEXT
...
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of problem symptoms. If multiple
suspected areas are listed, the potential causes of the symptoms are listed in order
...
Other materials about Toyota Venza:
Wireless Door Lock Tuner Circuit Malfunction (B1242)
DESCRIPTION
The door control receiver is used to receive electrical waves relating to the
entry functions of the smart key system. The certification ECU (smart key ECU assembly)
decodes the requested smart key system operation by identifying a key code ba ...
Short in Driver Side Squib 2nd Step Circuit (B1810/53-B1813/53)
DESCRIPTION
The driver side squib 2nd step circuit consists of the center airbag sensor assembly,
spiral cable and steering pad.
The center airbag sensor assembly uses this circuit to deploy the airbag when
deployment conditions are met.
These DTCs are ...
Removal
REMOVAL
PROCEDURE
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-)
battery terminal to disable the SRS system (See page
).
NOTICE:
When disconnecting the cable, s ...
0.1624