Toyota Venza: Steering Angle Sensor Communication Stop Mode

Toyota Venza Service Manual / Networking / Can Communication System / Steering Angle Sensor Communication Stop Mode

DESCRIPTION

Detection Item	Symptom	Trouble Area
Steering Angle Sensor Communication Stop Mode	"Steering Angle Sensor" is not displayed on "CAN Bus Check" screen of the Techstream. Applies to Steering Angle Sensor Communication Stop Mode in DTC Combination Table.	Power source circuit of steering angle sensor Steering angle sensor branch wire or connector Steering angle sensor

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
Turn the ignition switch off before inspecting CAN bus wires for a ground short.
After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

1.	CHECK CAN BUS WIRE FOR DISCONNECTION (STEERING ANGLE SENSOR BRANCH WIRE)

(a) Turn the ignition switch off.

(b) Disconnect the connector of the steering angle sensor.

Text in Illustration

*1	Front view of wire harness connector (to Steering Angle Sensor)

Standard Resistance:

Tester Connection	Switch Condition	Specified Condition
D35-4 (CANH) - D35-3 (CANL)	Ignition switch off	54 to 69 Ω

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (STEERING ANGLE SENSOR BRANCH WIRE)

2.	CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

(a) Turn the ignition switch to ON.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection	Switch Condition	Specified Condition
D35-5 (IG) - Body ground	Ignition switch ON	11 to 14 V

Text in Illustration

*1	Front view of wire harness connector (to Steering Angle Sensor)

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.	CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

(a) Turn the ignition switch off.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
D35-2 (ESS) - Body ground	Always	Below 1 Ω

Text in Illustration

*1	Front view of wire harness connector (to Steering Angle Sensor)

REPLACE STEERING ANGLE SENSOR

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)

Power Steering ECU Communication Stop Mode

DESCRIPTION Detection Item Symptom Trouble Area Power Steering ECU Communication Stop Mode "EPS" is not displayed on ...

Yaw Rate Sensor Communication Stop Mode

DESCRIPTION Detection Item Symptom Trouble Area Yaw Rate Sensor Communication Stop Mode "Yaw Rate/Decelerate Sensor" ...

Other materials about Toyota Venza:

Brake Switch "A" / "B" Correlation (P0504)
DESCRIPTION The stop light switch is a duplex system that transmits 2 signals: STP and ST1-. These 2 signals are used by the ECM to monitor whether or not the brake system is working properly. If signals which indicate the brake pedal is being depressed a ...

Clearance Warning Buzzer
Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE FRONT DOOR SCUFF PLATE LH 2. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH 3. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL 4. REMOVE NO. 1 CLEARANCE WARNING BUZZER ...

Power Mirror cannot be Adjusted with Power Mirror Switch
SYSTEM DESCRIPTION The main body ECU (driver side junction block assembly) detects the mirror adjust switch status and sends the signal to the outer mirror control ECU assembly via CAN communication. On receiving the signal, each outer mirror control ECU ...