Toyota Venza: Jam Protection Function does not Operate
DESCRIPTION
This symptom may occur for any of the windows.
The jam protection function operates within a specified range during the manual up or auto up operation.
CAUTION / NOTICE / HINT
NOTICE:
- The power window control system uses a multiplex communication system
(LIN communication system). Inspect the communication function by following
How to Proceed with Troubleshooting (See page
.gif)
). Troubleshoot the power window control
system after confirming that the communication system is functioning properly. - When the power window regulator motor assembly is reinstalled or replaced, the power window control system must be initialized.
- After a door glass or a door glass run has been replaced, the jam protection
function may operate unexpectedly when the auto up function is used. In
such cases, the auto up function can be reinitialized by repeating the following
operations at least 5 times:
- Close the power window by fully pulling up the power window regulator master switch assembly or power window regulator switch assembly and holding it at the auto up position.
- Open the power window by fully pushing down the power window regulator master switch assembly or power window regulator switch assembly.
PROCEDURE
|
1. |
PERFORM INITIALIZATION (APPLICABLE LOCATION) |
(a) Initialize the power window regulator motor assembly (applicable location)
(See page ).
|
.gif)
|
2. |
CHECK POWER WINDOW CONTROL SYSTEM (AUTO UP/DOWN FUNCTION) |
(a) Check if the power window auto up/down function operates normally (See page
).
OK:
Auto up/down function is normal.
| NG | .gif) |
GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table) |
|
|
3. |
CHECK JAM PROTECTION FUNCTION OPERATING RANGE |
(a) Check if the jam protection function operates normally for the applicable power window.
HINT:
The jam protection function will not operate within 4 mm (0.157 in.) of the fully closed position.
OK:
Jam protection function operates normally.
|
Result |
Proceed to |
|---|---|
|
OK |
A |
|
NG (Driver side power window) |
B |
|
NG (Front passenger side power window) |
C |
|
NG (Rear LH side power window) |
D |
|
NG (Rear RH side power window) |
E |
| A | |
END (PROBLEM DUE TO INITIALIZATION FAILURE) |
| B | |
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Driver Side) |
| C | |
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Side) |
| D | |
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear LH Side) |
| E | |
REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Rear RH Side) |
Auto Up Operation does not Fully Close Power Window (Jam Protection Function
is Activated)
DESCRIPTION
If a door glass or a power window regulator motor assembly does not operate smoothly,
the jam protection function may be triggered automatically, resulting in the auto
up function bei ...
Power Window Master Switch
Components
COMPONENTS
ILLUSTRATION
Removal
REMOVAL
PROCEDURE
1. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST
BASE PANEL
2. REMOVE POWER WINDOW REGULAT ...
Other materials about Toyota Venza:
CD Sound Skips
PROCEDURE
1.
CHECK CD
(a) Check that the CD is not deformed or cracked.
OK:
No deformation or cracks on the CD.
NG
END (CD IS FAULTY)
...
Precaution
PRECAUTION
1. PRECAUTION FOR DISCONNECTING THE BATTERY CABLE
NOTICE:
When disconnecting the cable from the negative (-) battery terminal, initialize
the following systems after the cable is reconnected:
System
See Procedure
...
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
Use these procedure to troubleshoot the sliding roof system.
*: Use the Techstream.
PROCEDURE
1.
VEHICLE BROUGHT TO WORKSHOP
NEXT
...
0.1493