Toyota Venza: Data List / Active Test

Toyota Venza Service Manual / Park Assist / Monitoring / Intuitive Parking Assist System / Data List / Active Test

DATA LIST / ACTIVE TEST

1. DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Body Electrical / Intuitive P/A / Data List.

(e) According to the display on the Techstream, read the Data List.

Intuitive P/A

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
Main Switch	Clearance sonar main switch/OFF or ON	OFF: Clearance sonar main switch off ON: Clearance sonar main switch on	-
Intuitive P/A ECU Type	Type of intuitive P/A ECU/Normal	Normal: Normal clearance sonar type	-
Fr Left Sensor	Front left sensor information/Undetect, Close R, Mid Y, Mid L Y, Freeze, Open or Blink	Undetect: Not detected Close R: Detected (Close-range) Mid Y: Detected (Medium-range) Mid L Y: Detected (Long-range) Freeze: Sensor frozen Open: Open in sensor Blink: All displays blinking	-
Fr Right Sensor	Front right sensor information/Undetect, Close R, Mid Y, Mid L Y, Freeze, Open or Blink	Undetect: Not detected Close R: Detected (Close-range) Mid Y: Detected (Medium-range) Mid L Y: Detected (Long-range) Freeze: Sensor frozen Open: Open in sensor Blink: All displays blinking	-
Rr Left Sensor	Rear left sensor information/Undetect, Close R, Mid Y, Mid L Y, Freeze, Open or Blink	Undetect: Not detected Close R: Detected (Close-range) Mid Y: Detected (Medium-range) Mid L Y: Detected (Long-range) Freeze: Sensor frozen Open: Open in sensor Blink: All displays blinking	-
Rr Left Center Sensor	Rear left center sensor information/Undetect, Close R, Mid Y, Mid L Y, Long Y, Freeze, Open or Blink	Undetect: Not detected Close R: Detected (Close-range) Mid Y: Detected (Medium-range) Mid L Y: Detected (Long-range) Long Y: Detected (Longest-range) Freeze: Sensor frozen Open: Open in sensor Blink: All displays blinking	-
Rr Right Center Sensor	Rear right center sensor information/Undetect, Close R, Mid Y, Mid L Y, Long Y, Freeze, Open or Blink	Undetect: Not detected Close R: Detected (Close-range) Mid Y: Detected (Medium-range) Mid L Y: Detected (Long-range) Long Y: Detected (Longest-range) Freeze: Sensor frozen Open: Open in sensor Blink: All displays blinking	-
Rr Right Sensor	Rear right sensor information/Undetect, Close R, Mid Y, Mid L Y, Freeze, Open or Blink	Undetect: Not detected Close R: Detected (Close-range) Mid Y: Detected (Medium-range) Mid L Y: Detected (Long-range) Freeze: Sensor frozen Open: Open in sensor Blink: All displays blinking	-
Rr Sensor Onset Range	Buzzer activation range (for rear center sensors)/Narrow or Wide	Narrow: 600 mm (23.6 in.) Wide: 1000 mm (39.4 in.) (Pole) Wide: 1500 mm (59.1 in.) (Wall)	Customized value displayed
Keep Sense Buzzer	Keep sense buzzer operation/Not Avail or Avail	Not Avail: Buzzer stops Avail: Buzzer sounds continuously	Customized value displayed
Fr & Rr Buzzer Volume	Buzzer volume setting/L, M1, M2, M3 or H	L: Low volume M1: Medium low volume M2: Medium volume M3: Medium high volume H: High volume	Customized value displayed
Reverse Range Front Sensor	Operation setting for front sensors/F or F Stop	F: Front sensors operate F Stop: Front sensors stop	Customized value displayed
Non P/R Range Rear Sensor	Operation setting for rear sensors (rear center, rear corner)/R, Rcrn or R Stop	R: All rear sensors operate Rcrn: Rear corner sensors operate R Stop: All rear sensors stop	Customized value displayed
Sensor Condition N	Front sensor operation/Not Avail or Avail	Not Avail: Front sensors not available Avail: Front sensors available	Customized value displayed
Parking Signal	Parking signal/OFF or ON	OFF: Shift lever in any position other than P ON: Shift lever in P	-
Reverse Signal	Reverse signal/OFF or ON	OFF: Shift lever in any position other than R ON: Shift lever in R	-
Vehicle Speed Info	Vehicle speed signal/Snr Stop or Snr Work	Snr Stop: Vehicle speed approximately 13 km/h (8.1 mph) or more (when accelerating) or approximately 9 km/h (5.6 mph) or more (when decelerating) Snr Work: Vehicle speed less than approximately 13 km/h (8.1 mph) (when accelerating) or less than approximately 9 km/h (5.6 mph) (when decelerating)	-
Sonar Detection	Sonar detection condition/Stop or Work	Stop: Sonar detection not operating Work: Sonar detection operating	-
Clearance Sonar ECU	ECU information/Normal or Abnormal	Normal: ECU normal Abnormal: ECU not normal	-
Rr Right Freezed History	Rear right sensor frozen history/Not Rec or Recorded	Not Rec: No record history Recorded: Record history	-
Rr Right Center Freezed History	Rear right center sensor frozen history/Not Rec or Recorded	Not Rec: No record history Recorded: Record history	-
Rr Left Center Freezed History	Rear left center sensor frozen history/Not Rec or Recorded	Not Rec: No record history Recorded: Record history	-
Rr Left Freezed History	Rear left sensor frozen history/Not Rec or Recorded	Not Rec: No record history Recorded: Record history	-
Fr Right Freezed History	Front right sensor frozen history/Not Rec or Recorded	Not Rec: No record history Recorded: Record history	-
Fr Left Freezed History	Front left sensor frozen history/Not Rec or Recorded	Not Rec: No record history Recorded: Record history	-
AT/MT Recognition	Transmission information/AT or Unknown	AT: Automatic Transmission Unknown: Unknown	-
# Codes	Number of stored trouble codes/min.: 0, max.: 255	Number of DTCs will be displayed	-

2. ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Body Electrical / Intuitive P/A / Active Test.

(e) According to the display on the Techstream, perform the Active Test.

Intuitive P/A

Tester Display	Test Part	Control Range	Diagnostic Note
Buzzer	No. 1 clearance warning buzzer	Operate or Stop	Confirm that the vehicle is stopped and the ignition switch is ON

Diagnosis System

DIAGNOSIS SYSTEM 1. DESCRIPTION (a) When troubleshooting a vehicle with a diagnosis system, the only difference from the usual troubleshooting procedure is connecting the Techstream to the vehicle ...

Dtc Check / Clear

DTC CHECK / CLEAR 1. CHECK DTC (a) Connect the Techstream to the DLC3. (b) Turn the engine switch on (IG). (c) Turn the clearance sonar main switch on. (d) Turn the Techstream on. (e) Enter the ...

Other materials about Toyota Venza:

Driving position memory
Your preferred driving position (the position of the driver’s seat and angle of the outside rear view mirrors) can be memorized and recalled by pressing a button. It is also possible to set this function to activate automatically when the doors are unl ...

Key-off Operation Function Operates even if Operating Conditions are not Satisfied
DESCRIPTION When the front doors are closed, each power window regulator motor assembly can control its power window operation for approximately 45 seconds after the ignition switch is turned from ON to off by receiving operation permission ...

Registration
REGISTRATION PROCEDURE 1. DESCRIPTION OF CODE REGISTRATION It is necessary to register the transmitter IDs in the tire pressure warning ECU when replacing a tire pressure warning valve and transmitter and/or a tire pressure warning ECU. Prepare all tra ...