Toyota Venza manuals

Toyota Venza: Data List / Active Test

DATA LIST / ACTIVE TEST

1. DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Sliding Roof / Data List.

(e) Read the Data List according to the display on the Techstream.

Sliding Roof (Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly))

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Open SW

SLIDE OPEN switch signal/ON or OFF

ON: SLIDE OPEN switch pressed

OFF: SLIDE OPEN switch not pressed

-

Close SW

SLIDE CLOSE switch signal/ON or OFF

ON: SLIDE CLOSE switch pressed

OFF: SLIDE CLOSE switch not pressed

-

Up SW

TILT UP switch signal/ON or OFF

ON: TILT UP switch pressed

OFF: TILT UP switch not pressed

-

Down SW

TILT DOWN switch signal/ON or OFF

ON: TILT DOWN switch pressed

OFF: TILT DOWN switch not pressed

-

Hall IC1 Pulse

Sliding roof operation signal/LO or HI

LO: Sliding roof motor not operating

HI: Sliding roof motor operating

-

Hall IC1 Status

Sliding roof operation signal/NORMAL or LOCK

NORMAL: Sliding roof motor operating

LOCK: Sliding roof motor not operating

-

Hall IC2 Pulse

Sliding roof operation signal/LO or HI

LO: Sliding roof motor not operating

HI: Sliding roof motor operating

-

Hall IC2 Status

Sliding roof operation signal/NORMAL or LOCK

NORMAL: Sliding roof motor operating

LOCK: Sliding roof motor not operating

-

Ignition (Direct Signal)

Ignition switch signal/ON or OFF

ON: Ignition switch ON

OFF: Ignition switch off

-

Ignition (MPX)

Ignition switch signal (MPX signal)/ON or OFF

ON: Ignition switch ON

OFF: Ignition switch off

-

Door Courtesy

Driver's door courtesy light switch signal/ON or OFF

ON: Driver's door open

OFF: Driver's door closed

-

Key Off Permission

Key-off sliding roof operation permit signal/ON or OFF

ON: Front doors are not opened within 45 seconds after ignition switch turned off

OFF: Any status except "ON" status

-

Open Switch Failure (Past)

Open switch failure signal (Past)/Fail or Not Fail

Fail: Sliding roof open signal failure (Past)

Not Fail: Sliding roof open signal not fail (Past)

-

Close Switch Failure (Past)

Close switch failure signal (Past)/Fail or Not Fail

Fail: Sliding roof close signal failure (Past)

Not Fail: Sliding roof close signal not fail (Past)

-

Up Switch Failure (Past)

Up switch failure signal (Past)/Fail or Not Fail

Fail: Sliding roof tilt up signal failure (Past)

Not Fail: Sliding roof tilt up signal not fail (Past)

-

Down Switch Failure (Past)

Down switch failure signal (Past)/Fail or Not Fail

Fail: Sliding roof tilt down signal failure (Past)

Not Fail: Sliding roof tilt down signal not fail (Past)

-

Open Switch Failure (Current)

Open switch failure signal (Current)/Fail or Not Fail

Fail: Sliding roof open signal failure (Current)

Not Fail: Sliding roof open signal not fail (Current)

-

Close Switch Failure (Current)

Close switch failure signal (Current)/Fail or Not Fail

Fail: Sliding roof close signal failure (Current)

Not Fail: Sliding roof close signal not fail (Current)

-

Up Switch Failure (Current)

Up switch failure signal (Current)/Fail or Not Fail

Fail: Sliding roof tilt up signal failure (Current)

Not Fail: Sliding roof tilt up signal not fail (Current)

-

Down Switch Failure (Current)

Down switch failure signal (Current)/Fail or Not Fail

Fail: Sliding roof tilt down signal failure (Current)

Not Fail: Sliding roof tilt down signal not fail (Current)

-

2. ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Sliding Roof / Active Test.

(e) Perform the Active Test according to the display on the Techstream.

Sliding Roof (Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly))

Tester Display

Test Part

Control Range

Diagnostic Note

Slide Roof

Operate sliding roof

CLOS/UP / OFF

-

Slide Roof

Operate sliding roof

OPN/DWN / OFF

-

Terminals Of Ecu
TERMINALS OF ECU 1. CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) (a) Disconnect the P4 ECU connector. (b) Measure the resistance and voltage according to the value(s) in the tabl ...

Dtc Check / Clear
DTC CHECK / CLEAR 1. CHECK DTC (a) Connect the Techstream to the DLC3. (b) Turn the ignition switch to ON. (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Sliding Roo ...

Other materials about Toyota Venza:

Back Door Motor Clutch Malfunction (B2225)
DESCRIPTION When an electrical malfunction (open or short) is detected in the clutch circuit of the power back door ECU (power back door motor unit) while the power back door is operating, the power back door ECU (power back door motor unit) stores DTC B2 ...

Electrical Key Oscillator(for Center Floor)
Components COMPONENTS ILLUSTRATION Installation INSTALLATION PROCEDURE 1. INSTALL ELECTRICAL KEY OSCILLATOR (a) Engage the clamp and install the electrical key oscillator. NOTICE: Be careful when installing the electrical key osci ...

Heated Oxygen Sensor
Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE NO. 1 ENGINE UNDER COVER 2. REMOVE NO. 2 ENGINE UNDER COVER 3. REMOVE FRONT EXHAUST PIPE ASSEMBLY 4. REMOVE HEATED OXYGEN SENSOR (a) Using SST, remove the heat ...

© 2016-2025 Copyright www.tovenza.com

0.148