PROBLEM SYMPTOMS TABLE
HINT:
Symptom |
Suspected Area |
See page |
---|---|---|
Theft deterrent system cannot be set |
Security indicator light circuit |
|
ECU power source circuit |
|
|
Front door lock assembly |
|
|
Rear door lock assembly |
|
|
Back door lock assembly |
|
|
Door courtesy switch circuit |
|
|
Back door lock assembly (back door courtesy switch) |
|
|
Engine hood courtesy switch circuit |
|
|
If the symptom(s) still occur after the above areas are inspected and proved to be normal, replace the main body ECU (driver side junction block assembly) |
|
|
Security indicator does not blink when theft deterrent system is set |
Security indicator light circuit |
|
If the symptom(s) still occur after the above area is inspected and proved to be normal, replace the main body ECU (driver side junction block assembly) |
|
|
Theft deterrent system can be set even when door is open |
Door courtesy switch circuit |
|
If the symptom(s) still occur after the above area is inspected and proved to be normal, replace the main body ECU (driver side junction block assembly) |
|
|
Theft deterrent system can be set even when engine hood is open. |
Engine hood courtesy switch circuit |
|
If the symptom(s) still occur after the above area is inspected and proved to be normal, replace the main body ECU (driver side junction block assembly) |
|
|
Vehicle horn(s) (low pitched, high pitched) do not sound while theft deterrent system is in warning operation |
Horn circuit |
|
If the symptom(s) still occur after the above area is inspected and proved to be normal, replace the main body ECU (driver side junction block assembly) |
|
|
Headlights do not blink while theft deterrent system is in warning operation |
Headlight relay circuit |
|
If the symptom(s) still occur after the above area is inspected and proved to be normal, replace the main body ECU (driver side junction block assembly) |
|
|
Taillights do not blink while theft deterrent system is in warning operation |
Taillight relay circuit |
|
If the symptom(s) still occur after the above area is inspected and proved to be normal, replace the main body ECU (driver side junction block assembly) |
|
|
Hazard warning lights do not flash while theft deterrent system is in warning operation |
Wire harness or connector |
- |
Turn signal flasher assembly |
|
|
If the symptom(s) still occur after the above areas are inspected and proved to be normal, replace the main body ECU (driver side junction block assembly) |
|
|
Interior light does not light up while theft deterrent system is in warning operation |
Interior light circuit |
|
If the symptom(s) still occur after the above area is inspected and proved to be normal, replace the main body ECU (driver side junction block assembly) |
|
|
Security horn does not sound while theft deterrent system is in warning operation |
Security horn circuit |
|
If the symptom(s) still occur after the above area is inspected and proved to be normal, replace the main body ECU (driver side junction block assembly) |
|
|
Headlights blink even when theft deterrent system is not set |
Headlight relay circuit |
|
If the symptom(s) still occur after the above area is inspected and proved to be normal, replace the main body ECU (driver side junction block assembly) |
|
|
Taillights blink even when theft deterrent system is not set |
Taillight Relay Circuit |
|
If the symptom(s) still occur after the above area is inspected and proved to be normal, replace the main body ECU (driver side junction block assembly) |
|
|
Hazard warning lights flash even when theft deterrent system is not set |
Wire harness or connector |
- |
Turn signal flasher assembly |
|
|
If the symptom(s) still occur after the above areas are inspected and proved to be normal, replace the main body ECU (driver side junction block assembly) |
|
|
Interior light comes on even when theft deterrent system is not set |
Interior light circuit |
|
If the symptom(s) still occur after the above area is inspected and proved to be normal, replace the main body ECU (driver side junction block assembly) |
|
Removal
REMOVAL
PROCEDURE
1. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP
2. REMOVE FRONT PILLAR GARNISH
3. REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
4. REMOVE FRONT NO. 4 SPEAKER ASSEMBLY (for 13 Speakers)
(a) Remove the 2 ...
Installation
INSTALLATION
PROCEDURE
1. INSTALL VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)
(a) Install the vacuum switching valve assembly (for ACIS) with the bolt.
Torque:
9.0 N·m {92 kgf·cm, 80 in·lbf}
...
Touch Panel Switch does not Function
PROCEDURE
1.
CHECK MULTI-DISPLAY
(a) Check if there is any foreign matter caught between the display and exterior
frame of the multi-display.
OK:
No foreign matter is caught between the display and exterior frame of the m ...