Toyota Venza: Problem Symptoms Table

Toyota Venza Service Manual / Seat / Front Power Seat Control System(w/ Memory) / Problem Symptoms Table

PROBLEM SYMPTOMS TABLE

HINT:

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
Inspect the fuses and relays related to this system before inspecting the suspected areas below.

Front Power Seat Control System (w/ Memory)

Symptom	Suspected Area	See page
Front Power Seat does not Operate with Front Power Seat Switch	Position control ECU and switch assembly
	Wire harness or connector	-
One or more Power Seat Motors do not Operate	Separate type front seat cushion assembly
	Position control ECU and switch assembly	-
	Wire harness or connector	-
Power Seat Position is not Memorized	Position control ECU and switch assembly
	Outer mirror control ECU assembly LH	-
	Main body ECU (driver side junction block assembly)	-
	Seat memory switch	-
	Wire harness or connector	-
Power Seat does not Return to Memorized Position	SFI system (for 1AR-FE)
	SFI system (for 2GR-FE)	-
	Lighting system (int)	-
	Position control ECU and switch assembly	-
	Main body ECU (driver side junction block assembly)	-
	Outer mirror control ECU assembly LH	-
Wireless Transmitter Memory Function does not Operate	Power door lock control system
	Lighting system (int)	-
	Smart key system (for start function)*	-
	Position control ECU and switch assembly	-
	Main body ECU (driver side junction block assembly)	-
	Certification ECU (smart key ECU assembly)*	-
Wireless-linked Return Function does not Operate	Wireless door lock control system (w/ smart key system)
	Wireless door lock control system (w/o smart key system)	-
	Lighting system (int)	-
	Smart key system (for entry function)*	-
	Main body ECU (driver side junction block assembly)	-
	Position control ECU and switch assembly	-
	Certification ECU (smart key ECU assembly)*	-
Power Seat Power Easy Access System Function does not Operate	Position control ECU and switch assembly
	Main body ECU (driver side junction block assembly)	-
	Front seat inner belt assembly LH	-
	Wire harness or connector	-
Only Lumbar Support Adjustment Function does not Operate	Front lumbar power seat switch
	Lumbar support adjuster assembly
	Wire harness or connector	-

*: w/ Smart Key System

Customize Parameters

CUSTOMIZE PARAMETERS 1. CUSTOMIZING FUNCTION WITH TECHSTREAM (REFERENCE) HINT: When the customer requests a change in a function, first make sure that the function can be customized. ...

Diagnosis System

DIAGNOSIS SYSTEM 1. DESCRIPTION (a) Front power seat control system (w/ Memory) data and Diagnostic Trouble Codes (DTCs) can be read through the Data Link Connector 3 (DLC3) of the vehicle. When ...

Other materials about Toyota Venza:

Removal
REMOVAL PROCEDURE 1. REMOVE WINDSHIELD WIPER MOTOR AND LINK (a) Remove the windshield wiper motor and link (See page ). 2. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY 3. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY 4. REMOVE COOL AIR INTAKE DUCT SEAL ...

Back Door Opener Switch
Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE BACK DOOR PANEL TRIM ASSEMBLY 2. REMOVE REAR LIGHT ASSEMBLY LH 3. REMOVE REAR LIGHT ASSEMBLY RH HINT: Use the same procedure for the RH side and LH side. 4. REMOVE BA ...

Back-up Power Source Circuit
DESCRIPTION The back-up power source circuit for the A/C amplifier is shown below. Power is supplied even when the ignition switch is turned off. The power is used for diagnostic trouble code memory, etc. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE ...