Toyota Venza manuals

Toyota Venza: Installation

INSTALLATION

PROCEDURE

1. INSTALL PARKING BRAKE SWITCH ASSEMBLY

(a) Install the parking brake switch assembly with the screw.

Torque:

0.9 N·m {9 kgf·cm, 8 in·lbf}


2. INSTALL PARKING BRAKE PEDAL ASSEMBLY

(a) Install the parking brake pedal assembly with the 3 nuts.

Torque:

21 N·m {214 kgf·cm, 15 ft·lbf}


(b) Connect the parking brake switch connector.


(c) Install the No. 1 parking brake cable assembly with the bolt and nut.


Torque:

Nut :

5.4 N·m {55 kgf·cm, 48 in·lbf}

Bolt :

15 N·m {153 kgf·cm, 11 ft·lbf}

(d) Connect the heated oxygen sensor connector and engage the 2 clamps (for 2GR-FE).


(e) Return the floor carpet assembly to an original state.

3. INSTALL CONSOLE BOX SUB-ASSEMBLY


4. INSTALL POSITION INDICATOR HOUSING ASSEMBLY


5. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY


6. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


7. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


8. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH


9. INSTALL FRONT DOOR SCUFF PLATE RH


10. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


11. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


12. INSTALL FRONT DOOR SCUFF PLATE LH


13. INSTALL AIR CONDITIONING CONTROL ASSEMBLY


14. INSTALL CONSOLE BOX ASSEMBLY


15. INSTALL NO. 2 CONSOLE BOX CARPET


16. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY (w/o Seat Heater System)


17. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY (w/ Seat Heater System)


18. INSTALL FRONT SEAT ASSEMBLY LH

HINT:

Refer to the instructions for Installation of the front seat assembly.

  • for Manual Seat:

  • for Power Seat:

19. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).


20. INSPECT BRAKE WARNING LIGHT


Inspection
INSPECTION PROCEDURE 1. INSPECT PARKING BRAKE SWITCH ASSEMBLY (a) Measure the resistance according to the value(s) in the table below. Standard Resistance: Tester ...

Parking Brake System
Problem Symptoms Table PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symp ...

Other materials about Toyota Venza:

On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (a) Inspect the shift lock operation. (1) Move the shift lever to P. (2) Turn the ignition switch off. (3) Check that the shift lever cannot be moved from P to any other position ...

Inspection
INSPECTION PROCEDURE 1. INSPECT INNER REAR VIEW MIRROR ASSEMBLY (a) Inspect operation of the electrochromic inner mirror. (1) Connect a positive (+) lead from the battery to terminal 1 and a negative (-) lead to terminal 2. (2) Press the AUTO switch. ...

Removal
REMOVAL PROCEDURE 1. REMOVE FRONT SEAT HEADREST ASSEMBLY 2. REMOVE FRONT SEAT REAR OUTER TRACK COVER 3. REMOVE FRONT SEAT REAR INNER TRACK COVER 4. REMOVE FRONT SEAT ASSEMBLY 5. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB 6. REMOVE RECL ...

© 2016-2025 Copyright www.tovenza.com

0.13