Toyota Venza: Customize Parameters

Toyota Venza Service Manual / Door / Hatch / Power Back Door System / Customize Parameters

CUSTOMIZE PARAMETERS

HINT:

The following items can be customized.

NOTICE:

After confirming whether the items requested by the customer are applicable or not for customization, perform customizing operations.
Be sure to record the current settings before customization.
When troubleshooting, make sure that the item in question is not set to "OFF" as a result of customization (Example: For the system, "the wireless function does not operate", first check that the wireless function is not set to "OFF", then perform troubleshooting).

1. CUSTOMIZE

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Customize Setting.

(e) Select the setting by referring to the table below.

Power Back Door System

Tester Display	Default	Content	Setting
Wireless Power Back Door Open	Lock:0.8s/Unlock:0.8s*2	Function that operates the power back door by pushing the transmitter switch.	Lock:OFF/Unlock:OFF Lock:OFF/Unlock:ON Lock:OFF/Unlock:Twice Lock:OFF/Unlock:0.8s Lock:Twice/Unlock:Twice Lock:0.8s/Unlock:0.8s
PBD SW Operation	0.8 s	Function that turns the power back door closer switch on when a switch is pushed once or held down for 0.8 sec. .	0.8 s or 0.0 s
PBD Buzzer*1	OFF	This function makes the power back door buzzer sound when the power back door is operating.	OFF or ON

Tester Display

Default

Content

Setting

Wireless Power Back Door Open

Lock:0.8s/Unlock:0.8s*2

Function that operates the power back door by pushing the transmitter switch.

Lock:OFF/Unlock:OFF

Lock:OFF/Unlock:ON

Lock:OFF/Unlock:Twice

Lock:OFF/Unlock:0.8s

Lock:Twice/Unlock:Twice

Lock:0.8s/Unlock:0.8s

PBD SW Operation

0.8 s

Function that turns the power back door closer switch on when a switch is pushed once or held down for 0.8 sec. .

0.8 s or 0.0 s

PBD Buzzer*1

OFF

This function makes the power back door buzzer sound when the power back door is operating.

OFF or ON

*1:The warning buzzer that sounds when the power back door is operating cannot be customized. (Even if this function is set to "off", the buzzer will still sound.)
*2: Default setting differs depending on the country

How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT HINT: Use the following procedures to troubleshoot the power back door system. *: Use the Techstream. PROCEDURE 1. VEHICLE BROUG ...

Operation Check

OPERATION CHECK 1. CHECK BASIC OPERATION (a) Conditions necessary for the power back door to open: The power back door main switch is off (switch is not pressed). The back door is unlock ...

Other materials about Toyota Venza:

Removal
REMOVAL PROCEDURE 1. REMOVE FRONT WHEEL LH 2. REMOVE FRONT FENDER OUTSIDE MOULDING LH 3. REMOVE FRONT FENDER LINER LH (a) Using a screwdriver, turn the pin 90 degrees and remove the 2 pin hold clips. Text in Illustration ...

Terminals Of Ecu
TERMINALS OF ECU 1. CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) (a) Disconnect the P4 ECU connector. (b) Measure the resistance and voltage according to the value(s) in the table below. HINT: Measure the values on the wire harness si ...

Reassembly
REASSEMBLY PROCEDURE 1. INSTALL FRONT SEAT WIRE RH (for Front Passenger Side) (a) Engage each clamp and install the front seat wire RH. 2. INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Side) 3. INSTALL SEAT POSITION SENSOR 4. INSTALL SEA ...