DESCRIPTION
This DTC is stored when items controlled by the certification ECU (smart key ECU assembly) cannot be customized via the navigation system vehicle customization screen.
HINT:
The certification ECU (smart key ECU assembly) controls the smart key system related items that are customizable via the navigation system vehicle customization screen.
|
DTC No. |
DTC Detection Condition |
Trouble Area |
|---|---|---|
|
B15F7 |
Certification ECU (smart key ECU assembly) vehicle setting processing malfunction |
|
CAUTION / NOTICE / HINT
NOTICE:
Before replacing the certification ECU (smart key ECU assembly), refer to Registration
(See page
).
PROCEDURE
|
1. |
CHECK CAN COMMUNICATION SYSTEM |
(a) Use the Techstream to check if the CAN communication system is functioning
normally (See page
).
OK:
CAN communication DTCs are not output.
| NG | |
GO TO CAN COMMUNICATION SYSTEM |
|
|
2. |
CHECK SMART KEY SYSTEM |
(a) for Entry Function:
Check if the smart key system is malfunctioning (See page
).
for Start Function:
Check if the smart key system is malfunctioning (See page
).
HINT:
Customization may not be possible depending on the malfunction in the smart key system.
OK:
No malfunctions are present in the smart key system.
(b) Proceed to the next step based on the check result.
|
Result |
Proceed to |
|---|---|
|
OK |
A |
|
NG (for Entry Function) |
B |
|
NG (for Start Function) |
C |
| B | |
GO TO SMART KEY SYSTEM (for Entry Function) |
| C | |
GO TO SMART KEY SYSTEM (for Start Function) |
|
|
3. |
CHECK CUSTOMIZE ITEMS |
(a) Make a note of the customizable items for the certification ECU (smart key ECU assembly) related system.
HINT:
The items shown as customizable via the navigation system vehicle customization screen can also be changed using the Techstream. In the following step, the Techstream will be used.
(1) To match-up the items on the navigation system vehicle customization screen
with the items on the Techstream, check the customize parameters list for the smart
key system (for Entry Function) related items that can be customized via the navigation
system vehicle customization screen (See page
).
(2) To match-up the items on the navigation system vehicle customization screen
with the items on the Techstream, check the customize parameters list for the smart
key system (for Start Function) related items that can be customized via the navigation
system vehicle customization screen (See page
).
(b) Using the Techstream, confirm that it is possible to change the settings of the customize parameters that are available for customization via the navigation system vehicle customization screen.
OK:
The items available for customization via the navigation system vehicle customization screen can be customized successfully using the Techstream.
| OK | |
REPLACE NAVIGATION RECEIVER ASSEMBLY |
| NG | |
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Main Body ECU Vehicle Information Reading/Writing Process Malfunction (B15F6)
XM Tuner Antenna Disconnected (B15FE,B15FF)Customize Parameters
CUSTOMIZE PARAMETERS
1. CUSTOMIZE FUNCTION WITH TECHSTREAM
NOTICE:
Be sure to record the current settings before customizing.
These buzzers should be ON for safe driving. Perform these procedure
only if it is necessary to set the buzzer OFF ...
System Description
SYSTEM DESCRIPTION
1. CRUISE CONTROL SYSTEM
This system is controlled by the ECM, and is activated by the throttle position
sensor and motor. The ECM controls the following functions: ON-OFF, - SET, + RES,
CANCEL, vehicle speed control, motor output cont ...
Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor) (P0327,P0328)
DESCRIPTION
Flat-type knock sensors (non-resonant type) have structures that can detect vibrations
between approximately 5 and 15 kHz.
Knock sensors are fitted onto the engine block to detect engine knocking.
The knock sensor contains a piezoelectric elem ...