Toyota Venza: Operation Check
OPERATION CHECK
1. CHECK AUTO OPERATION
NOTICE:
Make sure that initialization is completed before inspection (See page
.gif)
).
HINT:
When pressing the switch for 0.3 seconds or less, the roof glass moves but auto operation does not operate.
(a) Turn the ignition switch to ON.
(b) When the roof glass is fully closed, press the SLIDE OPEN switch for 0.3 seconds or more. Check that the roof glass automatically slides until it is fully opened.
(c) When the roof glass is fully closed, press the TILT UP switch for 0.3 seconds or more. Check that the roof glass automatically tilts up until it is fully tilted upward.
(d) When the auto operation is operating, check that pressing any sliding roof switch stops the roof glass operation.
2. CHECK SLIDING ROOF OPERATION AFTER IGNITION SWITCH IS TURNED OFF
(a) Turn the ignition switch from ON to off, and check that the sliding roof can be operated. Then open the driver or front passenger door once, and check that the sliding roof cannot be operated.
(b) Turn the ignition switch from ON to off and wait for approximately 43 seconds. Check that the sliding roof cannot be operated.
(c) Operate the auto operation (slide open or tilt up) with the driver front passenger door open. While the roof glass is in motion, turn the ignition switch off. Check that the roof glass stops immediately.
3. CHECK JAM PROTECTION FUNCTION
CAUTION:
- To avoid injury, do not use a part of your body to check the jam protection function.
- Do not allow anything to become caught in the sliding roof by accident while servicing.
- Perform the inspection from the inside of the vehicle.
NOTICE:
- To avoid damaging the roof, do not use hard objects such as a hammer to check the jam protection function.
- If the jam protection function does not operate, initialize the sliding
roof ECU (sliding roof drive gear sub-assembly) (See page
).
(a) When the slide close function is operating and an object is caught between the vehicle body and glass, check that the sliding roof moves in reverse direction.
(b) When the tilt down function is operating, and an object is caught between the vehicle body and the roof glass, check that the sliding roof tilts up fully.
4. CHECK SLIDING ROOF OPEN WARNING
(a) Open the sliding roof by using the sliding roof switch.
(b) When the ignition switch is turned from ON to off and the driver door is opened, check that the warning buzzer in the combination meter assembly sounds once. Then, check that the multi-information display on the accessory meter assembly displays "MOON ROOF OPEN"*.
*: w/ Rear View Monitor
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
Use these procedure to troubleshoot the sliding roof system.
*: Use the Techstream.
PROCEDURE
1.
VEHICLE BROUGHT TO WORKSHOP
...
Initialization
INITIALIZATION
1. INITIALIZE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
NOTICE:
When the sliding roof glass, sliding roof housing or sliding roof ECU
(sliding roof drive ge ...
Other materials about Toyota Venza:
Rear Airbag Sensor LH Circuit Malfunction (B1635/24)
DESCRIPTION
The side collision sensor LH circuit (to determine deployment of the front seat
side airbag assembly LH and curtain shield airbag assembly LH) is composed of the
center airbag sensor assembly, rear airbag sensor LH and side airbag sensor LH.
...
Front Left Sensor Malfunction (C1AE1)
DESCRIPTION
The No. 1 ultrasonic sensor (front left sensor) is installed on the front bumper.
The ECU detects obstacles based on signals received from the No. 1 ultrasonic sensor
(front left sensor). If the No. 1 ultrasonic sensor (front left sensor) has ...
Indicator Circuit
DESCRIPTION
The headlight beam level control system indicator light in the combination meter
assembly comes on for approximately 3 seconds when the ignition switch is turned
to ON. The indicator light also comes on when the headlight leveling ECU assembly ...
0.1533