INSTALLATION
PROCEDURE
1. CLEAN QUARTER WINDOW ASSEMBLY
(a) Clean the outer edges of the quarter window assembly with a non-residue solvent. NOTICE:
|
|
2. INSTALL QUARTER WINDOW ASSEMBLY
(a) Using a brush or a sponge, apply Primer M to the exposed part of the vehicle body.
NOTICE:
(b) Using a brush or a sponge, apply Primer G to the contact surface of the quarter window glass.
HINT:
If an area other than that specified is coated by accident, wipe off the primer with a non-residue solvent before it dries.
NOTICE:
(c) Apply adhesive to the quarter window assembly.
Adhesive:
Toyota Genuine Windshield Glass Adhesive or equivalent
(1) Cut off the tip of the cartridge nozzle as shown in the illustration. Standard Dimension:
|
|
(2) Load the sealer gun with cartridge.
(3) Apply adhesive to the quarter window glass as shown in the illustration.
(d) Install the quarter window glass to the vehicle body.
(1) Position the quarter window glass so that the matchmarks are aligned, and press it in gently along the rim (when a window with missing clips is used). Text in Illustration
|
|
(2) Lightly press the front surface of the windshield glass to ensure that the windshield glass is securely fit to the vehicle body (when a window with missing clips is used).
HINT:
Press the glass with a force of 98 N (10 kgf, 22 lbf) or more.
(3) Engage the 3 clips to install the quarter window glass (when a window without missing clips is used used). |
|
(4) Hold the quarter window assembly in place securely with protective tape or equivalent until the adhesive hardens.
NOTICE:
(5) Lightly press the outer surface of the glass to ensure that the glass is securely fit to the vehicle body.
(6) Using a scraper, remove any excess or protruding adhesive. HINT: Apply adhesive onto the glass rim. NOTICE: Do not drive the vehicle within the time described in the table below. Minimum Time:
|
|
3. INSPECT FOR LEAK AND REPAIR
(a) After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
(b) If water leaks into the cabin, allow the water to dry and add adhesive.
(c) Remove the protective tape.
4. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY
5. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for LH Side)
6. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH (for RH Side)
7. CONNECT REAR SEAT OUTER BELT ASSEMBLY
8. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY
9. INSTALL RECLINING REMOTE CONTROL BEZEL
10. INSTALL REAR SEAT ASSEMBLY LH (for LH Side)
11. INSTALL REAR SEAT NO. 2 RECLINING CONTROL CABLE SUB-ASSEMBLY (for LH Side)
12. INSTALL REAR SEAT OUTER TRACK BRACKET COVER (for LH Side)
13. INSTALL REAR SEAT INNER TRACK BRACKET COVER (for LH Side)
14. INSTALL REAR SEAT HEADREST ASSEMBLY (for LH Side)
15. INSTALL REAR SEAT ASSEMBLY RH (for RH Side)
16. INSTALL REAR SEAT RECLINING CONTROL CABLE SUB-ASSEMBLY (for RH Side)
17. INSTALL REAR SEAT OUTER TRACK BRACKET COVER (for RH Side)
18. INSTALL REAR SEAT INNER TRACK BRACKET COVER (for RH Side)
19. INSTALL REAR SEAT CENTER HEADREST ASSEMBLY (for RH Side)
20. INSTALL REAR SEAT HEADREST ASSEMBLY (for RH Side)
21. INSTALL REAR FLOOR FINISH PLATE
22. INSTALL REAR SEAT SUB FLOOR PANEL ASSEMBLY
23. INSTALL NO. 1 DECK BOARD
24. INSTALL DECK SIDE TRIM BOX RH
25. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY
26. INSTALL DECK SIDE TRIM BOX LH
27. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY
28. INSTALL DECK BOARD ASSEMBLY
29. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
30. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP
31. INSTALL REAR DOOR SCUFF PLATE
Key-off Operation Function Operates even if Operating Conditions are not Satisfied
DESCRIPTION
When the front doors are closed, each power window regulator motor assembly
can control its power window operation for approximately 45 seconds after
the ignition switch is turned from ON to off by receiving operation permission
...
Erasing the entire HomeLink® memory (all three programs)
Press and hold the 2 outside buttons for 10 seconds (or 20 seconds depending
on the model) until the indicator light flashes.
If you sell your vehicle, be sure to erase the programs stored in the HomeLink®
memory.
- Before programming
• Insta ...
Calculation formula for your vehicle
1. Cargo capacity
2. Total load capacity (vehicle capacity weight)
When 2 people with the combined weight of A lb. (kg) are riding in your vehicle,
which has a total load capacity (vehicle capacity weight) of B lb. (kg), the available
amount of cargo a ...