Toyota Venza manuals

Toyota Venza: Initialization

Toyota Venza Service Manual / Introduction / Repair Instruction / Initialization

INITIALIZATION

1. PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED/RECONNECTED

Necessary Procedure

Effect / Inoperative Function When Necessary Procedures are not Performed

See Page

Reset back door close position
  • Power back door function
  • Back door closer function


NOTICE:

  • It may not be possible to release the steering lock or start the engine when the battery voltage is low. If this occurs, initialization of the steering lock system is required. (See page )
  • Audio and Visual System:

    After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

  • Navigation System:

    After the ignition switch is turned off, the navigation receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

2. PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED

Replacement Part

Necessary Procedure

Effect / Inoperative Function when Necessary Procedures are not Performed

Note

ECM

Vehicle Identification Number (VIN) registration

MIL comes on

for 1AR-FE


for 2GR-FE

ECU communication ID registration (Engine immobiliser system)

Engine start

*1


*2
  • Throttle body
  • Cleaning the deposits from the throttle body
  • Engine assembly
  • Cylinder head sub-assembly
  • Camshaft (for intake or exhaust camshaft)
  • Camshaft timing gear assembly
  • Camshaft timing exhaust gear assembly
  • Piston or piston ring
  • Mass air flow meter sub-assembly
  • Fuel injector assembly
  • Fuel pump
  • Air fuel ratio sensor
  • Engine coolant temperature sensor
  • Spark plug
  • Ignition coil assembly
  • Air leaks from intake system
  • Gas leaks from exhaust system
  • Knock control sensor
  • Heated oxygen sensor

Inspection after repair
  • Poor idle, etc.
  • Engine start function, etc

for 1AR-FE
  • Throttle with motor body assembly
  • Engine assembly
  • Cylinder head sub-assembly
  • Camshaft (for intake or exhaust camshaft)
  • Camshaft timing gear assembly
  • Piston or piston ring
  • Mass air flow meter sub-assembly
  • Fuel injector assembly
  • Fuel pump
  • Air fuel ratio sensor
  • Heated oxygen sensor
  • Engine coolant temperature sensor
  • Spark plug
  • Ignition coil assembly
  • EGR valve assembly
  • Air leaks from intake system
  • Gas leaks from exhaust system
  • Knock control sensor

Inspection after repair
  • Poor idle, etc.
  • Engine start function, etc

for 2GR-FE

Automatic transaxle assembly
  1. Reset memory
  2. Transaxle compensation code Input
  3. Perform road test to allow TCM to Learn
  • Large shift shock
  • The deterioration of fuel efficiency

for U660F Initialization


for U660F Registration


for U760F Initialization


for U760F Registration


for U660E Initialization


for U660E Registration


for U760E Initialization


for U760E Registration
  • Valve body assembly
  • Shift solenoid valve SL3 and/or SL4
  1. Reset memory
  2. Reset transaxle compensation code
  3. Perform road test to allow TCM to learn
  • Large shift shock
  • The deterioration of fuel efficiency

Shift solenoid valve SL1 and/or SL2

Perform road test to allow TCM to learn
  • Large shift shock
  • The deterioration of fuel efficiency

TCM (If possible, read the transaxle compensation code from the previous TCM)

Possible
  1. Reset memory
  2. Transaxle compensation code input (Into the new TCM)
  3. Perform road test to allow TCM to learn
  • Large shift shock
  • The deterioration of fuel efficiency

Impossible
  1. Reset memory
  2. Reset transaxle compensation code
  3. Perform road test to allow TCM to learn
  • Large shift shock
  • The deterioration of fuel efficiency
  • Tire pressure warning ECU
  • Tire pressure warning valve and transmitter

Code registration (Tire pressure warning system)
  • When DTC detection conditions of "transmitter ID not received" DTC are met, TPWS indicator blinks for 1 minute, and then illuminates.
  • Tire pressure warning function

for registration

Brake actuator assembly (Skid control ECU)

Engine variant learning

VSC function


Power steering ECU

Rotation angle sensor initialization and torque sensor zero point calibration
  • P/S warning light comes on
  • EPS control


Steering column

Rotation angle sensor initialization and torque sensor zero point calibration

Steering effort is different between turning steering wheel to left and right

Roof console box assembly

Re-registration of codes in the garage door opener system

  • Register transmitter code
  • Rolling code systems

Garage door opener system


  • Certification ECU (smart key ECU assembly)*1
  • Steering lock ECU (steering lock actuator assembly)*1
  • Key*1

Code registration (Engine immobiliser system (w/ smart key system))
  • Wireless door lock control system
  • Smart key system
  • Engine start


Transponder key ECU*2
  1. Key code registration
  2. ECU communication ID registration

Engine start


  • Door control transmitter*2
  • Door control receiver*2

Registration of recognition code (Wireless door lock control system (w/o smart key system))

Wireless door lock control system


  • Occupant classification ECU
  • Front passenger seat
  1. Zero point calibration (Occupant classification system)
  2. Sensitivity check (Occupant classification system)
  • Occupant classification system
  • Passenger airbag ON/OFF indicator
  • Airbag system (Front passenger side)
  • Seat belt warning system (Front passenger side)


  • Power window regulator motor
  • Door window regulator

Initialize power window control system
  • Automatic door glass open/ close function
  • Jam protection function
  • Operation function after ignition switch is turned off
  • Remote control function


  • Sliding roof ECU (sliding roof drive gear assembly)
  • Sliding roof glass
  • Sliding roof housing

Initializing sliding roof ECU (pulse sensor initial position setting)
  • Automatic slide open, tilt up function of sliding roof
  • Jam protection function


  • Headlight leveling ECU
  • Rear height control sensor sub-assembly RH

Perform headlight leveling ECU initialization

Headlight leveling function


  • *1: w/ smart key system
  • *2: w/o smart key system
Customize Parameters
CUSTOMIZE PARAMETERS 1. INTUITIVE PARKING ASSIST SYSTEM (See page ) 2. POWER DOOR LOCK CONTROL SYSTEM (See page ) 3. WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Key System) (See page ) 4. ...

Terms
...

Other materials about Toyota Venza:

Certification ECU Vehicle Information Reading/Writing Process Malfunction (B15F7)
DESCRIPTION This DTC is stored when items controlled by the certification ECU (smart key ECU assembly) cannot be customized via the navigation system vehicle customization screen. HINT: The certification ECU (smart key ECU assembly) controls the smart k ...

Front Passenger Side Door Entry Lock Function does not Operate
DESCRIPTION If the front passenger door entry unlock function operates normally, but its entry lock function does not, this means that the request code from the front passenger door is being output normally. In this case, a malfunction in the lock sensor ...

Rear Light Assembly
Components COMPONENTS ILLUSTRATION On-vehicle Inspection ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT REAR LIGHT ASSEMBLY (a) Disconnect the connector from the rear light assembly. (b) Measu ...

© 2016-2026 Copyright www.tovenza.com

0.1758