DATA LIST / ACTIVE TEST
1. DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Back Door or Main Body / Data List.
(e) According to the display on the Techstream, read the "Data List".
Back Door (Power Back Door ECU*1 or Back Door Closer ECU*2)
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
---|---|---|---|
Door Lock Status |
Back door lock condition signal / LOCK or UNLOCK |
LOCK: Back door locked UNLOCK: Back door unlocked |
- |
Half Latch SW |
Half-latch switch signal / ON or OFF |
ON: Back door lock motor open-latched or over-latched OFF: Back door lock motor fully latched or half-latched |
- |
Closer Position SW |
Closer position switch signal / ON or OFF |
ON: Back door lock center gear in center position OFF: Back door lock center gear not in center position |
- |
Courtesy SW |
Back door courtesy switch signal / ON or OFF |
ON: Back door open OFF: Back door closed |
- |
PBD Touch Sensor (Right) |
Power back door touch sensor RH signal / ON or OFF |
OK: Power back door touch sensor RH pressed OFF: Power back door touch sensor RH not pressed |
- |
PBD Touch Sensor (Left) |
Power back door touch sensor LH signal / ON or OFF |
OK: Power back door touch sensor LH pressed OFF: Power back door touch sensor LH not pressed |
- |
IG SW |
Ignition switch / ON or OFF |
ON: Ignition switch ON OFF: Ignition switch off |
- |
# Codes |
The number of DTCs / min=0, max=255 |
The number of DTCs |
- |
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
---|---|---|---|
Back Door Open |
Back door lock / Permit or Prohibit |
Permit: Back door unlocked Prohibit: Back door locked |
- |
Back Door Open Handle SW |
Back door opener switch signal / ON or OFF |
ON: Back door opener switch on OFF: Back door opener switch off |
- |
2. ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Back Door / Active Test.
(e) According to the display on the Techstream, perform the "Active Test".
Back Door (Power Back Door ECU*1 or Back Door Closer ECU*2)
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
---|---|---|---|
Latch Release |
Back door lock latch |
ON / OFF |
- |
TS and CG Terminal Circuit
DESCRIPTION
In the Test Mode (signal check), a malfunction in the speed sensor that cannot
be detected when the vehicle is stopped can be detected while driving.
Transition to the sensor check mode can be performed by connecting terminals
TS and CG of th ...
Installation
INSTALLATION
PROCEDURE
1. INSTALL NAVIGATION RECEIVER ASSEMBLY
2. INSTALL NO. 2 RADIO RECEIVER BRACKET
(a) Install the No. 2 radio receiver bracket with the 4 screws.
Torque:
5.0 N·m {51 kgf·cm, 44 in·lbf}
3. INSTALL NO. 1 RADIO RECEIVER BRACKET
(a ...
Installation
INSTALLATION
PROCEDURE
1. INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING
(a) Engage the guide and install the rear door upper window frame moulding
to the door frame.
(b) Using an air riveter or ...