Toyota Venza manuals

Toyota Venza: Rear Airbag Sensor RH Circuit Malfunction (B1630/23)

Toyota Venza Service Manual / Supplemental Restraint Systems / Airbag System / Rear Airbag Sensor RH Circuit Malfunction (B1630/23)

DESCRIPTION

The side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH) is composed of the center airbag sensor assembly, rear airbag sensor RH and side airbag sensor RH.

The rear airbag sensor RH detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbag should be deployed.

DTC B1630/23 is stored when a malfunction is detected in the rear airbag sensor RH.

DTC No.

DTC Detection Condition

Trouble Area

B1630/23

  • Rear airbag sensor RH malfunction
  • Center airbag sensor assembly malfunction
  • Rear airbag sensor RH
  • Center airbag sensor assembly

WIRING DIAGRAM


PROCEDURE

1.

CHECK REAR AIRBAG SENSOR RH

(a) Turn the ignition switch off.


(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Interchange the rear airbag sensor LH with RH and connect the connectors to them.

(d) Connect the cable to the negative (-) battery terminal.

(e) Turn the ignition switch to ON, and wait for at least 60 seconds.

(f) Clear the DTCs stored in memory (See page ).


(g) Turn the ignition switch off.

(h) Turn the ignition switch to ON, and wait for at least 60 seconds.

(i) Check for DTCs (See page ).


Result

Proceed to

DTC B1630/23 is output.

A

DTC B1635/24 is output.

B

DTCs B1630/23 and B1635/24 are not output.

C

Text in Illustration

*1

Rear Airbag Sensor LH

*2

Center Airbag Sensor Assembly

HINT:

Codes other than DTCs B1630/23 and B1635/24 may be output at this time, but they are not related to this check.


A

REPLACE CENTER AIRBAG SENSOR ASSEMBLY


B

REPLACE REAR AIRBAG SENSOR RH


C

USE SIMULATION METHOD TO CHECK

Lost Communication with Rear Airbag Sensor RH (B1632/81,B1633/81,B1642/81,B1692/81,B1693/81)
DESCRIPTION The side collision sensor RH circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH) is composed of the center airbag sensor ...

Lost Communication with Front Satellite Sensor Bus (B161A/8A)
DESCRIPTION The front collision sensor circuit (front airbag sensor RH circuit and front airbag sensor LH circuit) is composed of the center airbag sensor assembly, front airbag sensor RH and fro ...

Other materials about Toyota Venza:

Automatic High Beam Camera (B124C)
DESCRIPTION The DTC is stored when the main body ECU (driver side junction block assembly) detects malfunctions in the camera (inner rear view mirror assembly). DTC No. DTC Detection Condition Trouble Area ...

Inspection
INSPECTION PROCEDURE 1. INSPECT TIE ROD ASSEMBLY LH (a) Secure the tie rod assembly LH in a vise. (b) Install the nut to the stud bolt. (c) Flip the ball joint back and forth 5 times. (d) Set a to ...

Installation
INSTALLATION PROCEDURE 1. INSTALL DRIVE MONITOR SWITCH (a) Engage the 4 claws to install the drive monitor switch. 2. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type) 3. INSTALL NAVIGATION RECEIVER ASSEMBLY WITH B ...

© 2016-2024 Copyright www.tovenza.com

0.1602