Toyota Venza manuals

Toyota Venza: Portable Player cannot be Connected Manually/Automatically

Toyota Venza Service Manual / Audio / Video / Audio And Visual System / Portable Player cannot be Connected Manually/Automatically

CAUTION / NOTICE / HINT

HINT:

Some versions of "Bluetooth" compatible audio players may not function properly, or the functions may be limited using the radio and display receiver assembly, even if the portable audio player itself can play files (See page ).


PROCEDURE

1.

CHECK CONNECTED DEVICE SETTINGS

(a) Check if the portable player is registered as a connected device.

NOTICE:

If a cellular phone is used as a portable player, it must be registered independently from the registration that is performed for the hands-free system.

HINT:

Only 5 portable players can be registered.

Result

Proceed to

The portable player is registered as a connected device.

A

The portable player is not registered as a connected device.

B


B

REGISTER PORTABLE PLAYER AS CONNECTED DEVICE


A

2.

CHECK SYMPTOMS

(a) Check the connection condition between the portable player and the radio and display receiver assembly.

The portable player cannot be connected under any of the following conditions:

  • The portable player is connected to another device.
  • The portable player is connected to the radio and display receiver assembly using the hands-free function.
  • The radio and display receiver assembly has cleared the portable player registration.
  • The portable player is off.

Result

Proceed to

The portable player cannot be connected automatically.

A

The portable player cannot be connected manually.

B


B

GO TO STEP 4


A

3.

CHECK AUTOMATIC CONNECTION SETTINGS

(a) Check the automatic connection settings of the "Bluetooth" audio.

(1) Check that the "Bluetooth" connection is on.

OK:

"Bluetooth" connection is on.


NG

TURN "Bluetooth" POWER TO ON


OK

4.

CHECK PORTABLE PLAYER STATUS

(a) Check the status of the portable player.

(1) Check that the portable player is not in standby mode.

(2) Check that the portable player is not connected to another device (headphones, etc.).

OK:

The portable player is not in standby mode and not connected to another device (headphones, etc.).


NG

TAKE PORTABLE PLAYER OUT OF STANDBY MODE AND DISCONNECT OTHER DEVICES (HEADPHONES, etc.)


OK

5.

CHECK USING ANOTHER "Bluetooth" AUDIO COMPATIBLE VEHICLE OF SAME MODEL

(a) Check if the portable player can be connected manually/automatically to another "Bluetooth" audio compatible vehicle of the same model.

OK:

The portable player can be connected manually/automatically.


NG

PORTABLE PLAYER IS NOT COMPATIBLE


OK

6.

REMOVE ADDITIONAL DEVICES WHICH USE RADIO WAVES

(a) Remove additional devices which use radio waves.

(b) Check if the portable player can be connected manually/automatically.

OK:

The portable player can be connected manually/automatically.


OK

END


NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

Noise Occurs or Sound Skips when Portable Player Plays
CAUTION / NOTICE / HINT HINT: Perform this check with the portable player volume set at an appropriate level. Make sure that there are no obstructions between the portable player ...

Registered Device cannot be Deleted
PROCEDURE 1. DELETE OPERATION (a) Check if a registered portable player can be deleted normally. OK: Registered portable player can be deleted normally. OK ...

Other materials about Toyota Venza:

On-vehicle Inspection
ON-VEHICLE INSPECTION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The procedure listed below is for the LH side. PROCEDURE 1. REMOVE REAR WHEEL 2. SEPARATE REAR FLEXIBLE HOSE 3. SEPARATE REAR DI ...

Turn signal lever
1. Right turn 2. Left turn 3. Move and hold the lever partway to signal a lane change. The right hand signal will flash until you release the lever. 4. Move and hold the lever partway to signal a lane change. The left hand signal will flash until you re ...

Terminals Of Ecu
TERMINALS OF ECU 1. CHECK MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY) (a) Disconnect the 2A and 2F main body ECU (driver side junction block assembly) connectors. (b) Measure the voltage and resistance according to the value(s) in the table be ...

© 2016-2019 Copyright www.tovenza.com

0.2155