Toyota Venza: Operation Check

Toyota Venza Service Manual / Lighting (int) / Lighting System / Operation Check

OPERATION CHECK

1. INSPECT ILLUMINATED ENTRY SYSTEM OPERATION

NOTICE:

Perform this inspection with the customize parameters at the initial setting.

HINT:

The interior light control illuminates the lights below.

Transponder Key Amplifier*1
Roof Console Box Assembly
Step or Spot Light Assembly
Engine Switch Illumination*2

(a) The operation and condition of this control are described below.

Operation	Condition
Fade in and illuminate constantly	Any door is opened when all doors are closed.
Illuminate for 15 seconds, and then fade out	When any of the following conditions is met, the lights illuminate for 15 seconds, and then fade out. The key enters any detection area around the doors when the ignition switch is off and all doors are closed*2. Any door is unlocked when the ignition switch is off, all doors are closed and all door are locked. The ignition switch is turned from ACC to off when all doors are closed. All doors are closed when any door is opened and the ignition switch is off.
Fade out immediately	When either of the following conditions is met, the lights fade out immediately. The ignition switch is turned from off to ACC when all doors are closed. All doors are locked when the ignition switch is off, all doors are closed and any door is unlocked.
Battery saver	When no changes occur in the condition of the doors for 20 minutes and a key is not inserted in the ignition key cylinder, these lights turn off1. When no changes occur in the condition of the doors for 20 minutes and a key is not in the detection area, these lights turn off2.

*1: w/o Smart Key System
*2: w/ Smart Key System

2. BATTERY SAVING CONTROL OPERATION

NOTICE:

Perform this inspection with the customize parameters at the initial settings.

HINT:

The lights controlled by battery saving control are as follows:

Transponder Key Amplifier*1
Engine Switch Illumination*2
Roof Console Box Assembly
Step or Spot Light Assembly
Courtesy Light Assembly
Vanity Light Assembly
No. 2 Room Light Assembly

(a) The operation and conditions of this control are described below.

Operation	Condition
Battery saving	When 20 minutes elapse after the ignition switch is turned from ACC or ON to off and the lights that operate remain on, the lights are turned off. HINT: Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off. The ignition switch is turned to ACC or ON. Any door is opened and closed. The back door is opened and closed. Any door is unlocked. The key enters any exterior actuation area.*2

Operation

Condition

Battery saving

When 20 minutes elapse after the ignition switch is turned from ACC or ON to off and the lights that operate remain on, the lights are turned off.

HINT:

Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off.

The ignition switch is turned to ACC or ON.
Any door is opened and closed.
The back door is opened and closed.
Any door is unlocked.
The key enters any exterior actuation area.*2

*1: w/o Smart Key System
*2: w/ Smart Key System

Customize Parameters

CUSTOMIZE PARAMETERS 1. CUSTOMIZING FUNCTION WITH TECHSTREAM HINT: The following items can be customized. NOTICE: When the customer requests a change in a function, first make sure that ...

Problem Symptoms Table

PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order ...

Other materials about Toyota Venza:

Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE STEERING RACK BOOT CLIP (for LH Side) (a) Using pliers, remove the steering rack boot clip. 2. REMOVE STEERING RACK BOOT CLIP (for RH Side) HINT: Perform the same procedure as for the LH side. 3. REMOVE NO. 2 STEERING RAC ...

Startability Malfunction (P1604)
DESCRIPTION This DTC is stored when the engine does not start even though the STA signal is input or when the engine takes a long time to start, and when the engine speed is low or the engine stalls just after the engine starts. Using the Techstream, the ...

Reassembly
REASSEMBLY PROCEDURE 1. INSTALL SHIFT SOLENOID VALVE SL4 (a) Coat the shift solenoid valve SL4 and bolt with ATF. Text in Illustration *1 Lock Plate *2 Solenoid V ...