Toyota Venza: Data List / Active Test
DATA LIST / ACTIVE TEST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
1. DATA LIST FOR CENTER AIRBAG SENSOR ASSEMBLY
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Enter the following menus: Body Electrical / SRS Airbag / Data List.
(f) Check the values by referring to the table below.
Data List|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
Driver Seat Position |
Driver Seat Position/ Forward: Seat position is forward Bkward: Seat position is backward Fail: Failure detected |
Forward/Bkward |
- |
|
Passenger Classification |
Passenger Classification/ NG: Date is not determined OFF: Vacant Child: Child (less than 32 kg (70.6 lb)) is seated AF05: Adult (36 to 54 kg (79.4 to 119.1 lb)) is seated AM50: Adult (more than 54 kg (119.1 lb)) is seated Fail: A failure is detected |
OFF/Child/AF05/AM50 |
- |
|
Left Side Buckle SW |
LH Side Buckle SW/ Unset: The seat belt is not fastened Set: The seat belt is fastened NG: Data is not determined |
Unset/Set |
- |
|
Right Side Buckle SW |
RH Side Buckle SW/ Unset: The seat belt is not fastened Set: The seat belt is fastened NG: Data is not determined |
Unset/Set |
- |
|
Display Type Information |
Display Type Information/ LR: The display is indicated by LH/RH DP: The display is indicated by Driver/Passenger |
LR |
- |
|
Number of Past DTC |
Number of Past DTC/ Min.: 0, Max.: 255 |
0 |
- |
Check Mode Procedure
CHECK MODE PROCEDURE
1. CHECK MODE (SIGNAL CHECK): DTC CHECK
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream ...
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
If a trouble code is displayed during the DTC check, check the circuit listed
for the code in the table below (refer to the appropriate page).
HINT:
When the ...
Other materials about Toyota Venza:
Installation
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.
PROCEDURE
1. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY
(a) Engage the 2 claws ...
Engine Immobiliser System Malfunction (B2799)
DESCRIPTION
This DTC is stored when one of the following occurs: 1) the ECM detects errors
in its own communications with the transponder key ECU assembly; 2) the ECM detects
errors in the communication lines; or 3) the ECU communication ID between the tr ...
Amplifier Antenna
Components
COMPONENTS
ILLUSTRATION
Removal
REMOVAL
PROCEDURE
1. REMOVE BACK DOOR PANEL TRIM ASSEMBLY
2. REMOVE AMPLIFIER ANTENNA ASSEMBLY
(a) Disconnect the 2 connectors.
(b) Remove th ...
0.141