Toyota Venza: Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
Front Wiper and Washer|
Symptom |
Suspected Area |
See page |
|---|---|---|
|
Front wipers and washer do not operate. |
FR WIP fuse |
- |
|
Windshield wiper switch assembly |
|
|
|
Harness or connector |
- |
|
|
Front wipers do not operate in INT. |
Windshield wiper switch assembly |
|
|
Windshield wiper motor assembly |
|
|
|
Harness or connector |
- |
|
|
Front wipers do not operate in LO. |
Windshield wiper switch assembly |
|
|
Windshield wiper motor assembly |
|
|
|
Harness or connector |
- |
|
|
Front wipers do not operate in HI. |
Windshield wiper switch assembly |
|
|
Windshield wiper motor assembly |
|
|
|
Harness or connector |
- |
|
|
Front washer motor does not operate. |
Windshield washer motor and pump assembly |
|
|
Windshield wiper switch assembly |
|
|
|
Harness or connector |
- |
|
|
Washer fluid does not flow. |
Washer hose and nozzle |
- |
|
Front wipers do not operate when front washer switch is ON. |
Windshield wiper switch assembly |
|
|
Windshield wiper motor assembly |
|
|
|
Harness or connector |
- |
|
|
When the front wiper switch is OFF, the wiper blades do not park or park in the wrong position. |
Front wiper arm installation position |
- |
|
Windshield wiper motor assembly |
|
|
|
Harness or connector |
- |
.gif)
|
Symptom |
Suspected Area |
See page |
|---|---|---|
|
Rear wiper and washer do not operate. |
RR WIP fuse |
- |
|
Windshield wiper switch assembly |
|
|
|
Harness or connector |
- |
|
|
Rear wiper does not operate in INT or HI. |
Windshield wiper switch assembly |
|
|
Rear wiper motor assembly |
|
|
|
Harness or connector |
- |
|
|
Rear washer motor does not operate. |
Windshield wiper switch assembly. |
|
|
Rear washer motor assembly |
|
|
|
Harness or connector |
- |
|
|
Washer fluid does not flow. |
Washer hose and nozzle |
- |
|
When the rear wiper switch is OFF, the wiper blade does not park or park in the wrong position. |
Rear wiper arm installation position |
- |
|
Rear wiper motor assembly |
|
|
Symptom |
Suspected Area |
See page |
|---|---|---|
|
Washer fluid level warning light does not operate. |
Washer level warning switch assembly |
|
|
Combination meter |
|
|
|
Harness or connector |
- |
Parts Location
PARTS LOCATION
ILLUSTRATION
ILLUSTRATION
...
Wiper Switch
...
Other materials about Toyota Venza:
Position Initialization Incomplete (B2343)
DESCRIPTION
This DTC is output when the sliding roof ECU (sliding roof drive gear sub-assembly)
has not been initialized.
DTC Code
DTC Detection Condition
Trouble Area
B2343
Sliding roof ECU (sli ...
Inspection
INSPECTION
PROCEDURE
1. INSPECT ATF TEMPERATURE SENSOR ASSEMBLY
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Condition
Sp ...
Combination Meter ECU Communication Stop Mode
DESCRIPTION
Detection Item
Symptom
Trouble Area
Combination Meter ECU Communication Stop Mode
"Combination Meter" is not displayed on "CAN Bus Check" screen
of t ...
0.1627