Toyota Venza manuals

Toyota Venza: Voice Recognition Microphone Disconnected (B1579)

Toyota Venza Service Manual / Navigation / Multi Info Display / Navigation System / Voice Recognition Microphone Disconnected (B1579)

DESCRIPTION

The navigation receiver assembly and inner rear view mirror assembly (amplifier microphone assembly) are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No.

DTC Detection Condition

Trouble Area

B1579

Telephone microphone signal is lost.

  • Inner rear view mirror assembly (amplifier microphone assembly)
  • Navigation receiver assembly
  • Harness or connector

WIRING DIAGRAM


PROCEDURE

1.

INSPECT NAVIGATION RECEIVER ASSEMBLY

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

E40-19 (MIN-) - Body ground

Always

Below 1 Ω

Text in Illustration

*a

Component with harness connected

(Navigation Receiver Assembly)



NG

REPLACE NAVIGATION RECEIVER ASSEMBLY


OK

2.

CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - INNER REAR VIEW MIRROR ASSEMBLY (AMPLIFIER MICROPHONE ASSEMBLY))

(a) Disconnect the E40 navigation receiver assembly connector.

(b) Disconnect the P12 inner rear view mirror assembly (amplifier microphone assembly) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

E40-6 (SNS2) - P12-10 (SGND)

Always

Below 1 Ω

E40-19 (MIN-) - P12-12 (MIC-)

Always

Below 1 Ω

E40-6 (SNS2) - Body ground

Always

10 kΩ or higher

E40-19 (MIN-) - Body ground

Always

10 kΩ or higher


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR


OK

3.

INSPECT INNER REAR VIEW MIRROR ASSEMBLY (AMPLIFIER MICROPHONE ASSEMBLY)

(a) Remove the inner rear view mirror assembly (amplifier microphone assembly) (See page ).


(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

10 (SGND) - 12 (MIC-)

Always

Below 1 Ω

Text in Illustration

*a

Component without harness connected

(Inner Rear View Mirror Assembly (Amplifier Microphone Assembly))



OK

REPLACE NAVIGATION RECEIVER ASSEMBLY


NG

REPLACE INNER REAR VIEW MIRROR ASSEMBLY (AMPLIFIER MICROPHONE ASSEMBLY)

LVDS Signal Malfunction (from Extension Module) (B1532)
DESCRIPTION The stereo component tuner assembly and the navigation receiver assembly are connected by the LVDS communication line. This DTC is stored when an LVDS communication error occurs betwee ...

Sending Malfunction (Navigation to APGS) (U0073,U0100,U0140,U0155)
DESCRIPTION These DTCs are stored when a malfunction occurs in the CAN communication circuit. DTC No. DTC Detection Condition Trouble Area U0073 ...

Other materials about Toyota Venza:

CD Sound Skips
PROCEDURE 1. CHECK CD (a) Check that the CD is not deformed or cracked. OK: No deformation or cracks on the CD. NG END (CD IS FAULTY) ...

Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of ...

Driver Side Door ECU Communication Stop (B2321)
DESCRIPTION This DTC is stored when LIN communication between the power window regulator motor assembly (for driver side) and main body ECU (driver side junction block assembly) stops for more than 10 seconds. DTC No. DTC Detection ...

© 2016-2024 Copyright www.tovenza.com

0.1244