Toyota Venza manuals

Toyota Venza: Voice Recognition Microphone Disconnected (B1579)

Toyota Venza Service Manual / Audio / Video / Audio And Visual System / Voice Recognition Microphone Disconnected (B1579)

DESCRIPTION

The radio and display receiver assembly and inner rear view mirror assembly (amplifier microphone assembly) are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No.

DTC Detection Condition

Trouble Area

B1579

Microphone signal is lost.

  • Inner rear view mirror assembly (amplifier microphone assembly)
  • Radio and display receiver assembly
  • Harness or connector

WIRING DIAGRAM


PROCEDURE

1.

INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

E42-19 (MIN-) - Body ground

Always

Below 1 Ω

Text in Illustration

*a

Component with harness connected

(Radio and Display Receiver Assembly)



NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY


OK

2.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - INNER REAR VIEW MIRROR ASSEMBLY (AMPLIFIER MICROPHONE ASSEMBLY))

(a) Disconnect the E42 radio and display receiver assembly connector.

(b) Disconnect the P12 inner rear view mirror assembly (amplifier microphone assembly) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

E42-6 (SNS2) - P12-10 (SGND)

Always

Below 1 Ω

E42-19 (MIN-) - P12-12 (MIC-)

Always

Below 1 Ω

E42-6 (SNS2) - Body ground

Always

10 kΩ or higher

E42-19 (MIN-) - Body ground

Always

10 kΩ or higher


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR


OK

3.

INSPECT INNER REAR VIEW MIRROR ASSEMBLY (AMPLIFIER MICROPHONE ASSEMBLY)

(a) Remove the inner rear view mirror assembly (amplifier microphone assembly) (See page ).


(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

10 (SGND) - 12 (MIC-)

Always

Below 1 Ω

Text in Illustration

*a

Component without harness connected

(Inner Rear View Mirror Assembly (Amplifier Microphone Assembly))



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY


NG

REPLACE INNER REAR VIEW MIRROR ASSEMBLY (AMPLIFIER MICROPHONE ASSEMBLY)

AV Signal Stoppage (Low Battery Voltage) (B158F)
DESCRIPTION This DTC is stored when a video or audio signal is interrupted due to battery voltage input to the radio and display receiver assembly dropping temporarily. DTC No. ...

USB Device Malfunction (B1585)
DESCRIPTION This DTC is stored when a malfunction occurs in a connected device. DTC No. DTC Detection Condition Trouble Area B1585 When a ...

Other materials about Toyota Venza:

Removal
REMOVAL PROCEDURE 1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM 2. DISCHARGE FUEL SYSTEM PRESSURE 3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD 4. REMOVE FRONT WHEELS 5. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL NOTICE: When disconnecting ...

Seat Belt Buckle Switch LH Circuit Malfunction (B1656/38)
DESCRIPTION The seat belt buckle switch LH circuit consists of the center airbag sensor assembly and front seat inner belt assembly LH. DTC B1656/38 is stored when a malfunction is detected in the seat belt buckle switch LH circuit. DTC No. ...

Installation
INSTALLATION PROCEDURE 1. INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY (a) Engage the adjuster positioning hole with the guide and install the front shoulder belt anchor adjuster assembly with the 2 bolts. Torque: 42 N·m {428 ...

© 2016-2024 Copyright www.tovenza.com

0.143