Toyota Venza: Vehicle Stability Control System
- Precaution
- Parts Location
- System Description
- System Diagram
- How To Proceed With Troubleshooting
- Calibration
- Check For Intermittent Problems
- Test Mode Procedure
- Problem Symptoms Table
- Terminals Of Ecu
- Diagnosis System
- Dtc Check / Clear
- Freeze Frame Data
- Fail-safe Chart
- Data List / Active Test
- Diagnostic Trouble Code Chart
- Steering Angle Sensor Initialization Incomplete (C1439/31,C1445/31)
- Performance Decline of Brake Function (C1441)
- Yaw Rate Sensor Output Malfunction (C1448/98)
- Control Module Communication Bus OFF (U0073/94,U0100/65,U0123/62,U0124/95,U0126/63)
- Stop Light Control Relay Malfunction (C1380/64)
- Skid Control ECU Malfunction (C1300/62)
- Brake Pedal Load Sensing Switch (C1267/67)
- ECU Version Miss Match (C1288/88)
- Open in Stop Light Switch Circuit (C1249/49)
- Master Cylinder Pressure Sensor Malfunction (C1246/46,C1281/81)
- Speed Sensor Rotor Faulty (C1237/37,C1275/75-C1278/78)
- Low Battery Positive Voltage or Abnormally High Battery Positive Voltage (C1241/41)
- Steering Angle Sensor Circuit Malfunction (C1231/31)
- Malfunction in Deceleration Sensor (C0365/28,C1234/34,C1245/32,C1245/45)
- Engine Control System Malfunction (C1201/51)
- Open or Short Circuit in ABS Solenoid Relay Circuit (C0278/11)
- Open or Short Circuit in ABS Motor Relay Circuit (C0273/13)
- SFR Solenoid Circuit (C0226/21,C0236/22,C0246/23,C0256/24,C1225/25-C1228/28)
- ABS Control System Malfunction (43)
- Rear Speed Sensor RH Circuit (C0210/33,C0215/34,C1273/73,C1274/74,C1332/38,C1333/39)
- Front Speed Sensor RH Circuit (C0200/31,C0205/32,C1271/71,C1272/72,C1330/35,C1331/36)
- ABS Warning Light Remains ON
- ABS Warning Light does not Come ON
- Brake Warning Light Remains ON
- Brake Warning Light does not Come ON
- TRAC OFF Indicator Light Remains ON
- TRAC OFF Indicator Light does not Come ON
- VSC OFF Indicator Light Remains ON
- VSC OFF Indicator Light does not Come ON
- Slip Indicator Light does not Come ON
- Slip Indicator Light Remains ON
- TC and CG Terminal Circuit
- TS and CG Terminal Circuit
Removal
REMOVAL
CAUTION / NOTICE / HINT
NOTICE:
Do not remove the steering angle sensor from the spiral cable.
HINT:
The steering angle sensor is a component of the spiral with sensor cable sub-assembly. ...
Precaution
PRECAUTION
1. PRECAUTION FOR DISCONNECTING THE BATTERY CABLE
NOTICE:
When disconnecting the cable from the negative (-) battery terminal, initialize
the following systems after the cable is recon ...
Other materials about Toyota Venza:
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of problem symptoms.
If multiple suspected areas are listed, the potential causes of the symptoms
are listed in order of probability in the "Suspected Area" ...
Internal Control Module EEPROM Error (P062F)
DESCRIPTION
The TCM monitors its internal operation and it will set this DTC when it detects
an internal malfunction.
DTC No.
DTC Detection Condition
Trouble Area
P062F
TCM internal error (EEPROM ...
Dtc Check / Clear
DTC CHECK / CLEAR
1. DTC CHECK (USING SST CHECK WIRE)
(a) Turn the ignition switch off.
(b) Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
SST: 09843-18040
(c) Turn the ignition switch to ON.
(d) Read and record any DTCs from the tire pre ...
0.1309