Toyota Venza manuals

Toyota Venza: Unlock Warning Switch Circuit

DESCRIPTION

The key unlock warning switch assembly turns on when the ignition key is inserted into the ignition key cylinder and turns off when the ignition key is removed.

The main body ECU (driver side junction block assembly) operates the key confinement prevention function while the key unlock warning switch assembly is on.

WIRING DIAGRAM


PROCEDURE

1.

READ VALUE USING TECHSTREAM (UNLOCK WARNING SWITCH ASSEMBLY)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Select the item below in the Data List and then read the display on the Techstream.

Main Body

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Key Unlock Warning SW

Unlock warning switch signal/ON or OFF

ON: Key inserted into ignition key cylinder

OFF: Key removed from ignition key cylinder

-

OK:

When the key is in the ignition key cylinder, ON appears on the Techstream.


OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE


NG

2.

INSPECT UNLOCK WARNING SWITCH ASSEMBLY

(a) Remove the unlock warning switch assembly (See page ).



(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D24-1 (UN+) - D24-2 (UN-)

Free

(Key removed)

10 kΩ or higher

D24-1 (UN+) - D24-2 (UN-)

Pushed

(Key set)

Below 1 Ω

Text in Illustration

*1

Component without harness connected

(Unlock Warning Switch Assembly)


NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY


OK

3.

CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - BODY GROUND)

(a) Disconnect the D24 unlock warning switch assembly connector.


(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D24-2 (UN-) - Body ground

Always

Below 1 Ω

Text in Illustration

*1

Front view of wire harness connector

(to Unlock Warning Switch Assembly)


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR


OK

4.

CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU)

(a) Disconnect the D51 main body ECU (driver side junction block assembly) connector.


(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D24-1 (UN+) - D51-5 (KSW)

Always

Below 1 Ω

Text in Illustration

*1

Front view of wire harness connector

(to Main Body ECU (Driver Side Junction Block Assembly))

*2

Front view of wire harness connector

(to Unlock Warning Switch Assembly)


OK

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

ECU Power Source Circuit
DESCRIPTION This circuit provides power for main body ECU (driver side junction block assembly) operation. WIRING DIAGRAM PROCEDURE 1. CHECK DRIVER SIDE JUNCTION BLOCK A ...

Transponder Key Amplifier
Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE FRONT DOOR SCUFF PLATE 2. REMOVE COWL SIDE TRIM SUB-ASSEMBLY 3. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PA ...

Other materials about Toyota Venza:

Short in Curtain Shield Squib RH Circuit (B1830/57-B1833/57)
DESCRIPTION The curtain shield squib RH circuit consists of the center airbag sensor assembly and curtain shield airbag assembly RH. The center airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met. These DTCs ...

Data Signal Circuit between Radio Receiver and Stereo Jack Adapter
DESCRIPTION The No. 1 stereo jack adapter assembly sends the sound data signal or image data signal from a USB device to the radio and display receiver assembly via this circuit. WIRING DIAGRAM PROCEDURE 1. CHECK HARNESS AND CONN ...

System Diagram
SYSTEM DIAGRAM Communication Table Sender Receiver Signal Line Main body ECU (Driver side junction block assembly) Power back door ECU (Power back door motor unit) ...

© 2016-2024 Copyright www.tovenza.com

0.1809