Toyota Venza: Ultrasonic Sensor(for Front Side)

Toyota Venza Service Manual / Park Assist / Monitoring / Ultrasonic Sensor(for Front Side)

Components

COMPONENTS

ILLUSTRATION

Removal

REMOVAL

PROCEDURE

1. REMOVE FRONT BUMPER ASSEMBLY

(See page )

2. REMOVE NO. 1 ULTRASONIC SENSOR

(a) Disengage the 2 claws to remove the No. 1 ultrasonic sensor.

HINT:

Use the same procedure for the RH side and LH side.

3. REMOVE NO. 2 ULTRASONIC SENSOR RETAINER

(a) Disengage the 2 claws to remove the No. 2 ultrasonic sensor retainer from the front bumper assembly.

HINT:

Use the same procedure for the RH side and LH side.

Inspection

INSPECTION

PROCEDURE

1. INSPECT NO. 1 ULTRASONIC SENSOR

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
1 (BI) - 5 (EI)	Always	10 kΩ or higher
1 (BI) - 2 (BO)	Always	10 kΩ or higher
3 (SI) - 4 (SO)	Always	Below 1 Ω
5 (EI) - 6 (EO)	Always	Below 1 Ω

Text in Illustration

*a	Component without harness connected (No. 1 Ultrasonic Sensor)

If the result is not as specified, replace the No. 1 ultrasonic sensor.

Installation

INSTALLATION

PROCEDURE

1. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER

(a) Engage the 2 claws to install the No. 2 ultrasonic sensor retainer to the front bumper assembly.

Text in Illustration

*a	Keyhole
*b	Snap

NOTICE:

Do not damage the front bumper assembly with the protrusion when installing the No. 2 ultrasonic sensor retainer.
Securely install the No. 2 ultrasonic sensor retainer so that there are no gaps between the retainer and surface of the front bumper assembly.

HINT:

When installing the No. 2 ultrasonic sensor retainer, align the keyhole and snap as shown in the illustration.
Use the same procedure for the RH side and LH side.

2. INSTALL NO. 1 ULTRASONIC SENSOR

(a) Engage the 2 claws to install the No. 1 ultrasonic sensor to the No. 2 ultrasonic sensor retainer.

NOTICE:

Push the No. 2 ultrasonic sensor retainer from the outside of the front bumper assembly when there is a gap between the No. 2 ultrasonic sensor retainer and the front bumper assembly surface. In this case, do not push on the No. 1ultrasonic sensor.

HINT:

Use the same procedure for the RH side and LH side.

3. INSTALL FRONT BUMPER ASSEMBLY

(See page )

Television Camera

Components COMPONENTS ILLUSTRATION ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE BACK DOOR PANEL TRIM ASSEMBLY 2. REMOVE REAR WIPER ARM HEAD CAP 3. REMOVE REAR WIPER ARM AND ...

Ultrasonic Sensor(for Rear Side)

...

Other materials about Toyota Venza:

Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of the problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column ...

Terminals Of Ecu
TERMINALS OF ECU 1. CHECK POWER BACK DOOR ECU (POWER BACK DOOR MOTOR UNIT) (w/ POWER BACK DOOR SYSTEM) (a) Disconnect the L20 power back door ECU connector. (b) Measure the voltage and resistance according to the value(s) in the table below. ...

Fail-safe Chart
FAIL-SAFE CHART 1. FAIL-SAFE FUNCTION If the following malfunctions occur, the AWD control ECU will stop the function of 4WD control system or partly change the function to control the system. If a malfunction occurs in the senso ...