Toyota Venza: U660e Automatic Transmission / Transaxle
- Atf Temperature Sensor(when Not Using The Engine Support Bridge)
- Atf Temperature Sensor(when Using The Engine Support Bridge)
- Automatic Transaxle Assembly(when Not Using The Engine Support Bridge)
- Automatic Transaxle Assembly(when Using The Engine Support Bridge)
- Automatic Transaxle Fluid
- Automatic Transaxle System
- Definition Of Terms
- Precaution
- Parts Location
- System Description
- System Diagram
- How To Proceed With Troubleshooting
- Mechanical System Tests
- Road Test
- Hydraulic Test
- Manual Shifting Test
- Registration
- Initialization
- Monitor Drive Pattern
- Problem Symptoms Table
- Diagnosis System
- Terminals Of Ecu
- Dtc Check / Clear
- Check Mode Procedure
- Fail-safe Chart
- Data List / Active Test
- Diagnostic Trouble Code Chart
- Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL) (P2769,P2770)
- Pressure Control Solenoid "G" Performance (Shift Solenoid Valve SL4) (P2808)
- Pressure Control Solenoid "G" Electrical (Shift Solenoid Valve SL4) (P2810)
- Lost Communication with ECM / PCM "A" (U0100)
- Torque Converter Clutch Pressure Control Solenoid Control Circuit Electrical (Shift Solenoid Valve SLU) (P2759)
- Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) (P2716)
- Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) (P2757)
- Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) (P2714)
- Pressure Control Solenoid "C" Electrical (Shift Solenoid Valve SL3) (P0798)
- Transmission Fluid Pressure Sensor / Switch "E" Circuit Low (P0989,P0990)
- Pressure Control Solenoid "C" Performance (Shift Solenoid Valve SL3) (P0796)
- Intermediate Shaft Speed Sensor "A" Circuit (P0791,P0793)
- Pressure Control Solenoid "B" Performance (Shift Solenoid Valve SL2) (P0776)
- Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2) (P0778)
- Pressure Control Solenoid "A" Electrical (Shift Solenoid Valve SL1) (P0748)
- Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1) (P0746)
- Brake Switch "B" Circuit High (P0724)
- Torque Converter Clutch Solenoid Performance (Shift Solenoid Valve SL) (P0741)
- Input / Turbine Speed Sensor Circuit Malfunction (P0715,P0717)
- Transmission Fluid Temperature Sensor "A" Performance (P0711)
- Transmission Fluid Temperature Sensor "A" Circuit Low Input (P0712,P0713)
- Transmission Range Sensor Circuit Malfunction (PRNDL Input) (P0705)
- Internal Control Module EEPROM Error (P062F)
- Vehicle Speed Sensor "A" (P0500)
- Starter Relay Circuit High (P0617)
- System Voltage (P0560)
- Transmission Control Switch Circuit
- ECU Power Source Circuit
- Automatic Transaxle Unit
- Differential Case
- Differential Oil Seal
- Oil Pump
- Park / Neutral Position Switch
- Shift Lever
- Speed Sensor(when Not Using The Engine Support Bridge)
- Speed Sensor(when Using The Engine Support Bridge)
- Tcm
- Torque Converter And Drive Plate
- Transmission Control Cable
- Transmission Wire(when Not Using The Engine Support Bridge)
- Transmission Wire(when Using The Engine Support Bridge)
- Valve Body Assembly(when Not Using The Engine Support Bridge)
- Valve Body Assembly(when Using The Engine Support Bridge)
Transfer System
Precaution
PRECAUTION
Prior to starting any work, clean the transfer assembly to prevent sand
or mud deposits from entering the assembly.
When removing any light alloy components su ...
Other materials about Toyota Venza:
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of problem symptoms. If multiple
suspected areas are listed, the potential causes of the symptoms are listed in order
of probability in the "Suspected Area" column of ...
Operation Check
OPERATION CHECK
1. AUTOMATIC LIGHT CONTROL SYSTEM OPERATION CHECK
(a) Turn the ignition switch to ON.
(b) Turn the light control switch to the AUTO position.
(c) Cover the automatic light control sensor.
(d) Check that the taillights and low beam headligh ...
Disassembly
DISASSEMBLY
PROCEDURE
1. REMOVE MAGNETIC SWITCH ASSEMBLY
(a) Remove the nut and disconnect the lead wire from the magnetic switch.
(b) Remove the 2 screws holding the magnetic switch to t ...
0.1343