Toyota Venza: Turn Signal Flasher Assembly
Components
COMPONENTS
ILLUSTRATION
Inspection
INSPECTION
PROCEDURE
1. INSPECT TURN SIGNAL FLASHER ASSEMBLY
|
(a) Disconnect the D34 turn signal flasher assembly connector. |
|
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
D34-1 (IG) - Body ground |
Ignition switch off |
Below 1 V |
|
Ignition switch ON |
11 to 14 V |
|
|
D34-4 (B) - Body ground |
Always |
11 to 14 V |
|
*1 |
Front view of wire harness connector (to Turn Signal Flasher Assembly) |
If the result is not as specified, repair or replace the wire harness or connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
D34-5 (EL) - Body ground |
Turn signal switch off |
10 kΩ or higher |
|
Turn signal switch in left turn position |
Below 1 Ω |
|
|
D34-6 (ER) - Body ground |
Turn signal switch in neutral position |
10 kΩ or higher |
|
Turn signal switch in right turn position |
Below 1 Ω |
|
|
D34-7 (E) - Body ground |
Always |
Below 1 Ω |
|
D34-8 (HAZ) - Body ground |
Hazard warning switch off |
10 kΩ or higher |
|
Hazard warning switch on |
Below 1 Ω |
If the result is not as specified, repair or replace the wire harness or connector.
|
(d) Reconnect the D34 turn signal flasher assembly connector. |
|
(e) Measure the voltage according to the valve(s) in the table below.
Standard Voltage:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
D34-2 (LR) - Body ground |
Hazard warning switch off |
Below 1 V |
|
Hazard warning switch on |
11 to 14 V (60 to 120 times per minute) |
|
|
Turn signal switch off |
Below 1 V |
|
|
Ignition switch ON and turn signal switch in RH position |
11 to 14 V (60 to 120 times per minute) |
|
|
D34-3 (LL) - Body ground |
Hazard warning switch off |
Below 1 V |
|
Hazard warning switch on |
11 to 14 V (60 to 120 times per minute) |
|
|
Turn signal switch off |
Below 1 V |
|
|
Ignition switch ON and turn signal switch in LH position |
11 to 14 V (60 to 120 times per minute) |
|
*1 |
Component with harness connected (Turn Signal Flasher Assembly) |
If the result is not as specified, replace the turn signal flasher assembly.
Removal
REMOVAL
PROCEDURE
1. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
HINT:
Refer to the procedure up to Remove Instrument Panel Safety Pad Assembly (See
page .gif)
).
2. REMOVE TURN SIGNAL FLASHER ASSEMBLY
|
(a) Disconnect the connector. |
|
(b) Disengage the clamp and remove the turn signal flasher assembly.
Installation
INSTALLATION
PROCEDURE
1. INSTALL TURN SIGNAL FLASHER ASSEMBLY
|
(a) Engage the clamp to install the turn signal flasher assembly. |
|
.png)
(b) Connect the connector.
2. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY
HINT:
Refer to the procedure from Install Instrument Panel Safety Pad Assembly (See
page .gif)
).
Stop Light Switch
Components
COMPONENTS
ILLUSTRATION
Removal
REMOVAL
PROCEDURE
1. REMOVE STOP LIGHT SWITCH ASSEMBLY
(a) Disconnect the connector.
...
Mirror (ext)
...
Other materials about Toyota Venza:
Security Horn Circuit
DESCRIPTION
When the theft deterrent system is switched from the armed state to the alarm
sounding state, the main body ECU (driver side junction block assembly) controls
the security horn.
WIRING DIAGRAM
PROCEDURE
1.
PERFORM A ...
Removal
REMOVAL
PROCEDURE
1. REMOVE FRONT SEAT HEADREST ASSEMBLY
2. REMOVE FRONT SEAT REAR OUTER TRACK COVER
3. REMOVE FRONT SEAT REAR INNER TRACK COVER
4. REMOVE FRONT SEAT ASSEMBLY
5. REMOVE RECLINING POWER SEAT SWITCH KNOB
6. REMOVE SLIDE AND VER ...
Automatic door locking and unlocking systems
The following functions can be set or canceled:
- Setting and canceling the functions
► Setting and canceling the functions
Vehicles with TFT type multi-information display The function settings can be changed
using the multi-information dis ...
0.1566