Toyota Venza: Trouble in Passenger Airbag ON/OFF Indicator

Toyota Venza Service Manual / Supplemental Restraint Systems / Occupant Classification System / Trouble in Passenger Airbag ON/OFF Indicator

DESCRIPTION

The occupant classification system detects the front passenger seat condition. It then informs a passenger of the front passenger airbag assembly and front seat belt pretensioner RH condition (activated/not activated) with the passenger airbag ON/OFF indicator.

HINT:

Approximately 6 seconds after the ignition switch is turned to ON, the passenger airbag ON/OFF indicator will be ON/OFF depending on the conditions listed below.

Front Passenger Seat Condition	Passenger Airbag ON/OFF Indicator		SRS Warning Light
Front Passenger Seat Condition	ON Indicator	OFF Indicator	SRS Warning Light
Vacant	OFF	OFF	OFF
Adult is seated.	ON	OFF	OFF
Child is seated.	OFF	ON	OFF
Child restraint system is set.	OFF	ON	OFF
Occupant classification system failure	OFF	ON	ON

PROCEDURE

1.	CHECK SRS WARNING LIGHT

(a) Turn the ignition switch to ON, and check the SRS warning light condition.

HINT:

If this trouble occurs, the SRS warning light is off. If the light is on, a DTC is output. Troubleshoot for the output DTC.

OK:

After the primary check period, the SRS warning light goes off.

HINT:

The primary check is performed for approximately 6 seconds after the ignition switch is turned to ON.

GO TO DTC CHART

2.	PERFORM ZERO POINT CALIBRATION

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(d) Using the Techstream, perform Zero Point Calibration (See page ).

OK:

"Zero Point Calibration is complete." is displayed.

GO TO STEP 4

3.	PERFORM SENSITIVITY CHECK

(a) Using the Techstream, perform Sensitivity Check (See page ).

Standard:

27 to 33 kg (59.5 to 72.8 lb)

END

4.	RETIGHTEN FRONT SEAT ASSEMBLY RH BOLT

(a) Turn the ignition switch off.

(b) Loosen the 4 installation bolts of the front seat assembly RH.

Torque:

37 N·m {377 kgf·cm, 27 ft·lbf}

5.	PERFORM ZERO POINT CALIBRATION

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

OK:

"Zero Point Calibration is complete." is displayed.

GO TO STEP 7

6.	PERFORM SENSITIVITY CHECK

(a) Using the Techstream, perform Sensitivity Check (See page ).

Standard:

27 to 33 kg (59.5 to 72.8 lb)

END

7.	READ VALUE USING PASSENGER SIDE BUCKLE SWITCH

(a) Turn the ignition switch to ON.

(b) Using the Techstream, read the "Data List" (See page ).

(1) Read the display when the passenger side buckle switch is operated.

Occupant Detection

Tester Display	Measurement Item / Range	Normal Condition	Diagnostic Note
Passenger Buckle SW	Passenger side buckle switch/ Set: The seat belt is fastened Unset: The seat belt is not fastened NG: Data is not determined	Unset/Set	-

Tester Display

Measurement Item / Range

Normal Condition

Diagnostic Note

Passenger Buckle SW

Passenger side buckle switch/

Set: The seat belt is fastened

Unset: The seat belt is not fastened

NG: Data is not determined

Unset/Set

OK:

The Techstream display changes correctly in accordance with the operation of the buckle switch.

GO TO STEP 12

8.	CHECK CONNECTORS

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal.

(d) Check that the terminals of connectors are not damaged.

OK:

The terminals are not deformed or damaged.

REPLACE FRONT SEAT WIRE RH

9.	REPLACE OCCUPANT CLASSIFICATION ECU

(a) Connect the connectors to the 4 occupant classification sensors.

(b) Replace the occupant classification ECU (See page ).

10.	PERFORM ZERO POINT CALIBRATION

(a) Connect the cable to the negative (-) battery terminal.

(b) Connect the Techstream to the DLC3.

(d) Using the Techstream, perform Zero Point Calibration (See page ).

OK:

"Zero Point Calibration is complete." is displayed.

11.	PERFORM SENSITIVITY CHECK

(a) Using the Techstream, perform Sensitivity Check (See page ).

Standard:

27 to 33 kg (59.5 to 72.8 lb)

END

12.	CHECK CONNECTORS

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal.

(d) Check that the terminals of connectors are not damaged.

OK:

The terminals are not deformed or damaged.

REPLACE FRONT SEAT WIRE RH

13.	REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

(a) Connect the connector to the occupant classification ECU.

(b) Replace the front seat inner belt assembly RH (See page ).

14.	PERFORM ZERO POINT CALIBRATION

(a) Connect the cable to the negative (-) battery terminal.

(b) Connect the Techstream to the DLC3.

(d) Using the Techstream, perform Zero Point Calibration (See page ).

OK:

"Zero Point Calibration is complete." is displayed.

15.	PERFORM SENSITIVITY CHECK

(a) Using the Techstream, perform Sensitivity Check (See page ).

Standard:

27 to 33 kg (59.5 to 72.8 lb)

END

Front Occupant Classification Sensor LH Circuit Malfunction (B1780)

DESCRIPTION The front occupant classification sensor LH circuit consists of the occupant classification ECU and front occupant classification sensor LH. DTC B1780 is recorded when a malfunction is ...

Rear Airbag Sensor

...

Other materials about Toyota Venza:

Fail-safe Chart
FAIL-SAFE CHART HINT: If the following conditions are detected while the cruise control is in operation, the system clears the stored vehicle speed in the ECM and cancels the cruise control operation. Vehicle Condition Auto Cancel ...

Torque Sensor Zero Point Adjustment Undone (C1515,C1525)
DESCRIPTION These DTCs do not indicate a malfunction. The power steering ECU stores these DTCs when it determines that the rotation angle sensor value initialization and torque sensor zero point calibration have not been performed. DTC No. ...

System Diagram
SYSTEM DIAGRAM Communication Table Transmitting ECU (Transmitter) Receiving ECU (Receiver) Signal Communication Method Certification ECU (smart key ECU assembly) Power management contro ...