Toyota Venza: Theft Deterrent System Communication Line High Fixation (B279A)

Toyota Venza Service Manual / Theft Deterrent / Keyless Entry / Engine Immobiliser System(w/ Smart Key System) / Theft Deterrent System Communication Line High Fixation (B279A)

DESCRIPTION

If the communication line (EFIO - IMI) to the certification ECU (smart key ECU assembly) is stuck high output (e.g. shorted to +B), the ECM stores this DTC.

DTC No.	DTC Detection Condition	Trouble Area
B279A	When the communication line (EFIO - IMI) between ECM and certification ECU (smart key ECU assembly) is stuck high output.	Wire harness or connector Certification ECU (Smart key ECU assembly) ECM

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

If the certification ECU (smart key ECU assembly) is replaced, register the key (See page ).

PROCEDURE

1.	CHECK DTC OUTPUT

(a) Clear the DTCs (See page ).

(b) Recheck for DTCs (See page ).

HINT:

If any DTCs other than DTC B279A are output, troubleshoot those DTCs first.

Result	Proceed to
DTC B279A is output	A
DTC B279A and other DTCs are output	B

GO TO DIAGNOSTIC TROUBLE CODE CHART

2.	CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ECM)

(a) Disconnect the certification ECU (smart key ECU assembly) connector.

(b) Disconnect the ECM connector.

Standard Resistance:

for 2GR-FE

Tester Connection	Condition	Specified Condition
D25-35 (EFIO) - A41-40 (IMI)	Always	Below 1 Ω
D25-35 (EFIO) - Body ground	Always	10 kΩ or higher

for 1AR-FE

Tester Connection	Condition	Specified Condition
D25-35 (EFIO) - A49-11 (IMI)	Always	Below 1 Ω
D25-35 (EFIO) - Body ground	Always	10 kΩ or higher

Standard Voltage:

Tester Connection	Condition	Specified Condition
D25-35 (EFIO) - Body ground	Always	Below 1 V

Text in Illustration

*1	Front view of wire harness connector (to Certification ECU (Smart Key ECU Assembly))
*2	Front view of wire harness connector (to ECM)
*3	for 2GR-FE
*4	for 1AR-FE

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.	CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Reconnect the certification ECU (smart key ECU assembly) connector.

(b) Reconnect the ECM connector.

Waveform (Reference):

Item	Content
Terminal No. (Symbol)	D25-35 (EFIO) - D25-15 (E)
Tool Setting	5 V/DIV., 100 msec./DIV.
Condition	Engine switch on (IG)

OK:

Waveform is output normally (see illustration).

Result	Proceed to
NG	A
OK (for 2GR-FE)	B
OK (for 1AR-FE)	C

Text in Illustration

Component with harness connected

(Certification ECU (Smart Key ECU Assembly))

GND

REPLACE ECM

4.	REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

(a) Replace the certification ECU (smart key ECU assembly) (See page ).

5.	KEY REGISTRATION

(a) Register the key (See page ).

6.	REGISTER ECU COMMUNICATION ID

(a) Register the ECU communication ID (See page ).

7.	CHECK DTC OUTPUT

(a) Clear the DTCs (See page ).

(b) Recheck for DTCs (See page ).

OK:

DTC B279A is not output.

Result	Proceed to
OK	A
NG (for 2GR-FE)	B
NG (for 1AR-FE)	C

END (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

REPLACE ECM

Diagnostic Trouble Code Chart

DIAGNOSTIC TROUBLE CODE CHART HINT: If a trouble code is stored during the DTC check, inspect the trouble areas listed for that code. For details of the code, refer to the "See page" bel ...

Short to GND in Immobiliser System Power Source Circuit (B278A)

DESCRIPTION This DTC is stored when the engine switch power source supply line is open or shorted. DTC No. DTC Detection Condition Trouble Area B2 ...

Other materials about Toyota Venza:

Entry Answer-back Buzzer does not Sound
DESCRIPTION The smart key system uses the wireless door lock buzzer to perform various vehicle exterior warnings. When the conditions for each warning are met, the certification ECU (smart key ECU assembly) sends a buzzer request signal to the main body E ...

Removal
REMOVAL PROCEDURE 1. REMOVE REAR WHEELS 2. REMOVE CENTER EXHAUST PIPE ASSEMBLY (a) Remove the center exhaust pipe assembly. HINT: Refer to the instructions for Removal of the exhaust pipe (See page for 2GR-FE, for 1AR-FE). 3. REMOVE LOWER NO. 1 EXH ...

Lost Communication with Gateway Module (Power Management1) (U1002)
DESCRIPTION The power management control ECU will store this DTC when no signals can be received from the ECUs that have been memorized as those that are connected to the CAN No. 2 bus. When the power management control ECU receives a respo ...