Toyota Venza manuals

Toyota Venza: Terminals Of Ecu

TERMINALS OF ECU

1. CHECK POWER STEERING ECU


HINT:

As connector z8 uses a lock lever, each terminal cannot be checked while the connector is still connected to the power steering ECU.

Terminal No. (Symbol)

Wiring Color

Terminal Description

z8-1 (V)

W

V phase motor output

z8-2 (U)

B

U phase motor output

z8-3 (W)

R

W phase motor output

(a) Measure the voltage and resistance according to the value(s) in the table below.

NOTICE:

When the P/S warning light is illuminated during a malfunction, the fail-safe function may cause the voltage of the power steering ECU terminals to become 0 V.

Terminal No. (Symbol)

Wiring Color

Terminal Description

Condition

Specified Condition

D19-1 (PIG) - D19-2 (PGND)

R - B

Power source

Always

11 to 14 V

D19-2 (PGND) - Body ground

B - Body ground

Power ground

Always

Below 1 Ω

D20-1 (CANH) - D20-7 (CANL)

BR - W

CAN communication line

Ignition switch off

54 to 69 Ω

D20-6 (IG) - D19-2 (PGND)

GR - B

IG power source

Ignition switch ON

11 to 14 V

z9-1 (RZV) - D19-2 (PGND)

R - B

Rotation angle sensor excitation output signal

Engine running, steering wheel being turned

-2.42 to 2.42 V

z9-3 (RZG) - D19-2 (PGND)

B - B

Rotation angle sensor excitation circuit GND

Always

Below 1 Ω

z9-5 (RZCS) - D19-2 (PGND)

L - B

Rotation angle sensor COS aspect output signal

Engine running, steering wheel being turned

-0.73 to 0.73 V

z9-6 (RZSN) - D19-2 (PGND)

Y - B

Rotation angle sensor SIN aspect output signal

Engine running, steering wheel being turned

-0.73 to 0.73 V

z10-5 (TRQ1) - z10-8 (TRQG)

W - B

Torque sensor signal

Engine running, steering wheel not turned (without load)

2.3 to 2.7 V

Engine running, steering wheel turned to right with vehicle stopped

2.5 to 3.8 V

Engine running, steering wheel turned to left with vehicle stopped

1.2 to 2.5 V

z10-6 (TRQV) - z10-8 (TRQG)

R - B

Torque sensor voltage source

Ignition switch ON

4.5 to 5.5 V

z10-7 (TRQ2) - z10-8 (TRQG)

Y - B

Torque sensor signal

Engine running, steering wheel not turned (without load)

2.3 to 2.7 V

Engine running, steering wheel turned to right with vehicle stopped

1.2 to 2.5 V

Engine running, steering wheel turned to left with vehicle stopped

2.5 to 3.8 V

z10-8 (TRQG) - Body ground

B - Body ground

Torque sensor ground

Always

Below 1 Ω

If the result is not as specified, the ECU may have a malfunction.

Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are lis ...

Diagnosis System
DIAGNOSIS SYSTEM 1. CHECK DLC3 (a) Check the DLC3 (See page ). 2. FUNCTION OF P/S WARNING LIGHT (a) When a malfunction is detected in the power steering system, the P/S warning light on the acc ...

Other materials about Toyota Venza:

Engine Hood Courtesy Switch Circuit
DESCRIPTION The security courtesy switch is installed together with the hood lock. This switch turns off when the engine hood is opened and turns on when the engine hood is closed. WIRING DIAGRAM PROCEDURE 1. INSPECT HOOD LOCK AS ...

Parts Location
PARTS LOCATION ILLUSTRATION ILLUSTRATION ILLUSTRATION ILLUSTRATION ILLUSTRATION ...

System Description
SYSTEM DESCRIPTION 1. ENGINE IMMOBILISER SYSTEM DESCRIPTION The engine immobiliser system is designed to prevent the vehicle from being stolen. This system uses the transponder key ECU assembly that stores the key codes of authorized ignition keys. If an ...

© 2016-2024 Copyright www.tovenza.com

0.1551