Toyota Venza: Terminals Of Ecm
TERMINALS OF ECM
1. CHECK ECM
|
Terminal No. (Symbol) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
|---|---|---|---|---|
|
A49-7 (TC) - B58-104 (E1) |
V - BR |
Terminal TC of DLC3 |
Ignition switch ON |
11 to 14 V |
|
A49-7 (TC) - B58-104 (E1) |
V - BR |
Terminal TC of DLC3 |
Terminals TC and CG of DLC3 connected |
Below 1 V |
|
A49-29 (STP) - B58-104 (E1) |
G - BR |
Stop light switch signal |
Brake pedal depressed |
7.5 to 14 V |
|
A49-29 (STP) - B58-104 (E1) |
G - BR |
Stop light switch signal |
Brake pedal released |
Below 1 V |
|
A49-39 (ST1-) - B58-104 (E1) |
V - BR |
Stop light switch signal |
Ignition switch ON Brake pedal depressed |
Below 1 V |
|
A49-39 (ST1-) - B58-104 (E1) |
V - BR |
Stop light switch signal |
Ignition switch ON Brake pedal released |
7.5 to 14 V |
|
A49-40 (CCS) - B58-104 (E1) |
P - BR |
Cruise control main switch signal |
Ignition switch ON |
11 to 14 V |
|
A49-40 (CCS) - B58-104 (E1) |
P - BR |
Cruise control main switch signal |
CANCEL switch on |
6.6 to 10.1 V |
|
A49-40 (CCS) - B58-104 (E1) |
P - BR |
Cruise control main switch signal |
- SET switch on |
4.5 to 7.1 V |
|
A49-40 (CCS) - B58-104 (E1) |
P - BR |
Cruise control main switch signal |
+ RES switch on |
2.3 to 4.0 V |
|
A49-40 (CCS) - B58-104 (E1) |
P - BR |
Cruise control main switch signal |
MAIN switch on |
Below 1 V |
|
Terminal No. (Symbol) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
|---|---|---|---|---|
|
A41-16 (TC) - B39-81 (E1) |
V - W |
Terminal TC of DLC3 |
Ignition switch ON |
11 to 14 V |
|
A41-16 (TC) - B39-81 (E1) |
V - W |
Terminal TC of DLC3 |
Terminals TC and CG of DLC3 connected |
Below 1 V |
|
A41-36 (STP) - B39-81 (E1) |
G - W |
Stop light switch signal |
Brake pedal depressed |
7.5 to 14 V |
|
A41-36 (STP) - B39-81 (E1) |
G - W |
Stop light switch signal |
Brake pedal released |
Below 1 V |
|
A41-35 (ST1-) - B39-81 (E1) |
V - W |
Stop light switch signal |
Ignition switch ON Brake pedal depressed |
Below 1 V |
|
A41-35 (ST1-) - B39-81 (E1) |
V - W |
Stop light switch signal |
Ignition switch ON Brake pedal released |
7.5 to 14 V |
|
A41-45 (CCS) - B39-81 (E1) |
P - W |
Cruise control main switch signal |
Ignition switch ON |
11 to 14 V |
|
A41-45 (CCS) - B39-81 (E1) |
P - W |
Cruise control main switch signal |
CANCEL switch on |
6.6 to 10.1 V |
|
A41-45 (CCS) - B39-81 (E1) |
P - W |
Cruise control main switch signal |
- SET switch on |
4.5 to 7.1 V |
|
A41-45 (CCS) - B39-81 (E1) |
P - W |
Cruise control main switch signal |
+ RES switch on |
2.3 to 4.0 V |
|
A41-45 (CCS) - B39-81 (E1) |
P - W |
Cruise control main switch signal |
MAIN switch on |
Below 1 V |
Diagnosis System
DIAGNOSIS SYSTEM
1. DESCRIPTION
The ECM controls the cruise control system of the vehicle. The data and DTCs
relating to the cruise control system can be read from the DLC3 of the vehicle.
If ei ...
Dtc Check / Clear
DTC CHECK / CLEAR
1. CHECK DTC
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Cruise Control / ...
Other materials about Toyota Venza:
Removal
REMOVAL
PROCEDURE
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-)
battery terminal to disable the SRS system.
NOTICE:
When disconnecting the cable, some systems ne ...
Adjustment
ADJUSTMENT
PROCEDURE
1. PRECAUTIONS AND WORK DESCRIPTION
(a) The U660E automatic transaxle does not have an oil filler tube and oil level
gauge. When adding fluid, add fluid through the refill hole on the transaxle case.
The fluid level can be adjusted ...
Vehicle Lift And Support Locations
VEHICLE LIFT AND SUPPORT LOCATIONS
1. NOTICE ABOUT VEHICLE CONDITION WHEN RAISING VEHICLE
(a) The vehicle must be unloaded before jacking up or raising the vehicle. Never
jack up or raise a heavily loaded vehicle.
(b) When removing any heavy components li ...
0.1304