Toyota Venza: System Description

Toyota Venza Service Manual / Tire Pressure Monitoring / Tire Pressure Warning System / System Description

SYSTEM DESCRIPTION

1. DESCRIPTION OF SYSTEM

(a) Each tire pressure warning valve and transmitter is equipped with a tire pressure sensor and a transmitter and is installed in each tire and wheel assembly. The sensor measures the tire pressure. The measured value and transmitter ID are transmitted to the tire pressure warning antenna and receiver on the body as radio waves and then sent to the tire pressure warning ECU from the tire pressure warning antenna and receiver. If the transmitter ID has already been registered, the ECU compares the measured air pressure value with the standard value. When the value is less than the standard value registered in the tire pressure warning ECU, the warning light on the accessory meter comes on.

2. INITIAL CHECK

(a) After the ignition switch is turned to ON, the tire pressure warning light comes on for 3 seconds and then goes off.

HINT:

If the warning light does not come on for 3 seconds, troubleshoot the tire pressure warning light circuit (See page ).

3. WHEN TIRE PRESSURE WARNING LIGHT IS LIT

(a) When the tire pressure warning light does not go off, or when it comes on while driving, check the tire pressure. If the tire pressure warning light comes on within several hours of adjusting the tire pressure, the tire may have a slow leak.

(b) Under the following conditions, the system may not function properly:

(1) The system will not function properly in the following conditions:

(When the condition becomes normal, the system will work properly.)

If tires not equipped with tire pressure warning valve and transmitters are used.
If the ID code on the tire pressure warning valve and transmitters is not registered in the tire pressure warning ECU.
If the tire inflation pressure is absolute pressure: 600 kPa (6.0 kgf/cm2, 87 psi) or more; relative pressure: 500 kPa (5.0 kgf/cm2, 73 psi) or more.
If the tire pressure warning valve and transmitter battery voltage drops (battery life: 10 years).

(2) The system may not function properly in the following conditions:

(When the condition becomes normal, the system will work properly.)

If electronic devices or facilities using similar radio wave frequencies are nearby.
If a radio set at similar frequencies is used in the vehicle.
If a window tint that affects the radio wave signal is installed.
If there is a lot of snow or ice on the vehicle, in particular around the wheels or wheel housings.
If non-genuine wheels are used.
If tire chains are used.

4. FUNCTION OF COMPONENTS

Component	Function
Tire pressure warning valve and transmitter	Combined as a single unit with a tire valve, it measures tire pressure and temperature and transmits an ID number for identification. Has a built-in battery.
Tire pressure warning antenna and receiver	Receives signals from the transmitters and transmits them to the tire pressure warning ECU.
Tire pressure warning ECU	Receives a signal from the receiver and identifies it as vehicle's own signal. If the measured value is equal to or lower than the specified value, it transmits a signal to illuminate the tire pressure warning light on the accessory meter.
Tire pressure warning light	Located in the accessory meter, it informs the driver of low tire pressure and system failures.

How To Proceed With Troubleshooting

CAUTION / NOTICE / HINT HINT: Use the following procedures to troubleshoot the tire pressure warning system. *: Use the Techstream. PROCEDURE 1. VEHICL ...

Registration

REGISTRATION PROCEDURE 1. DESCRIPTION OF CODE REGISTRATION It is necessary to register the transmitter IDs in the tire pressure warning ECU when replacing a tire pressure warning valve and transm ...

Other materials about Toyota Venza:

Trailer towing tips
Your vehicle will handle differently when towing a trailer. Help to avoid an accident, death or serious injury, keep the following in mind when towing: • Speed limits for towing a trailer vary by state or province. Do not exceed the posted towing speed ...

Cursor or Map Rotates when Vehicle Stopped
PROCEDURE 1. CHECK CONDITION (a) Check with the customer if the vehicle has been turned by a turntable. OK: Vehicle has not been turned by a turntable. HINT: If the vehicle is turned on a turntable with ...

Removal
REMOVAL PROCEDURE 1. REMOVE YAW RATE AND ACCELERATION SENSOR HINT: Refer to the instructions for Removal of the yaw rate and acceleration sensor (See page ). 2. REMOVE REAR NO. 2 AIR DUCT 3. REMOVE REAR NO. 1 AIR DUCT 4. REMOVE FRONT NO. 2 FLOO ...