Toyota Venza: SRS Warning Light does not Come ON

Toyota Venza Service Manual / Supplemental Restraint Systems / Airbag System / SRS Warning Light does not Come ON

DESCRIPTION

The SRS warning light is located on the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

When terminals TC and CG of the DLC3 are connected, the DTC is displayed by blinking of the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the center airbag sensor assembly in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.

A malfunction in this circuit is not recorded in the center airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the center airbag sensor assembly to the combination meter assembly through the CAN communication system and multiplex communication system.

WIRING DIAGRAM

PROCEDURE

1.	CHECK BATTERY VOLTAGE

(a) Measure the voltage of the battery.

Standard Voltage:

11 to 14 V

Result

Result	Proceed to
OK	A
NG (for 2GR-FE)	B
NG (for 1AR-FE)	C

INSPECT CHARGING SYSTEM AND BATTERY

2.	CHECK CONNECTOR

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

OK:

The connector is properly connected.

HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

(d) Disconnect the connector from the combination meter assembly.

(e) Check that the terminal of the connector is not damaged.

OK:

The terminal is not deformed or damaged.

REPLACE WIRE HARNESS

3.	CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)

(a) Connect the cable to the negative (-) battery terminal.

(b) Turn the ignition switch to ON.

Standard Voltage:

Tester Connection	Condition	Specified Condition
E2-14 (B) - Body ground	Always	11 to 14 V
E2-13 (IG+) - Body ground	Ignition switch ON	11 to 14 V

(d) Turn the ignition switch off.

(e) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
E2-24 (ES) - Body ground	Always	Below 1 Ω

Text in Illustration

*1	Front view of wire harness connector (to Combination Meter Assembly)

REPLACE WIRE HARNESS

4.	CHECK SRS WARNING LIGHT

(a) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(b) Connect the connector to the combination meter assembly.

(d) Connect the cable to the negative (-) battery terminal.

(e) Turn the ignition switch to ON.

(f) Check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and remains on.

HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.

REPLACE CENTER AIRBAG SENSOR ASSEMBLY

REPLACE COMBINATION METER ASSEMBLY

SRS Warning Light Remains ON

DESCRIPTION The SRS warning light is located on the combination meter assembly. When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turn ...

TC and CG Terminal Circuit

DESCRIPTION DTC output mode is set by connecting terminals TC and CG of the DLC3. DTCs are displayed by blinking of the SRS warning light. HINT: When each warning light stays blinking, a g ...

Other materials about Toyota Venza:

Problem Symptoms Table
PROBLEM SYMPTOMS TABLE Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column ...

Short in Passenger Side Airbag Variable Vent Hole Squib Circuit (B181A/7A-B181D/7A)
DESCRIPTION The passenger side airbag variable vent hole squib circuit consists of the center airbag sensor assembly and front passenger airbag assembly. The center airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions ...

Cup holders
► Front ► Rear Pull down the armrest and open the lid. - Adjusting size of the front cup holder Remove the adapter. CAUTION - Items unsuitable for the cup holder Do not place anything other than cups or aluminum cans in the ...