Toyota Venza manuals

Toyota Venza: Sliding Roof ECU Communication Stop (B1273)

Toyota Venza Service Manual / Networking / Lin Communication System / Sliding Roof ECU Communication Stop (B1273)

DESCRIPTION

This DTC is stored when LIN communication between the sliding roof ECU (sliding roof drive gear sub-assembly) and main body ECU (driver side junction block assembly) stops for more than 10 seconds.

DTC No.

DTC Detection Condition

Trouble Area

B1273

No communication between the sliding roof ECU (sliding roof drive gear sub-assembly) and main body ECU (driver side junction block assembly) for more than 10 seconds.

  • Sliding roof ECU (Sliding roof drive gear sub-assembly)
  • Main body ECU (Driver side junction block assembly)
  • Wire harness or connector
  • S/ROOF fuse

WIRING DIAGRAM


CAUTION / NOTICE / HINT

NOTICE:

  • When the sliding roof ECU (sliding roof drive gear sub-assembly) is replaced or removed and reinstalled, it requires initialization (See page ).

  • When using the Techstream to troubleshoot with the ignition switch off:

    Connect the Techstream to the DLC3, and turn the courtesy switch on and off at 1.5-second intervals until communication between the Techstream and vehicle begins.

PROCEDURE

1.

CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - BATTERY AND BODY GROUND)

(a) Disconnect the P4 ECU connector.


(b) Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

P4-2 (E) - Body ground

Always

Below 1 Ω

Standard Voltage:

Tester Connection

Condition

Specified Condition

P4-1 (B) - Body ground

Always

11 to 14 V

Text in Illustration

*1

Front view of wire harness connector

(to Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly))


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR


OK

2.

CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SLIDING ROOF ECU)

(a) Disconnect the D48 ECU connector.


(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

D48-10 (LIN2) - P4-4 (LIN)

Always

Below 1 Ω

P4-4 (LIN) - Body ground

Always

10 kΩ or higher

Text in Illustration

*1

Front view of wire harness connector

(to Main Body ECU (Driver Side Junction Block Assembly))

*2

Front view of wire harness connector

(to Sliding Roof ECU (Sliding Roof Drive Gear Sub-assembly))


NG

REPAIR OR REPLACE HARNESS OR CONNECTOR


OK

3.

REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

(a) Replace the sliding roof ECU (sliding roof drive gear sub-assembly) (See page ).



NEXT

4.

CHECK DTC OUTPUT

(a) Clear the DTC (See page ).


(b) Recheck for DTCs.

OK:

DTC B1273 is not output.


OK

END (SLIDING ROOF ECU WAS DEFECTIVE)


NG

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

Driver Side Door ECU Communication Stop (B2321)
DESCRIPTION This DTC is stored when LIN communication between the power window regulator motor assembly (for driver side) and main body ECU (driver side junction block assembly) stops for more th ...

LIN Communication Master Malfunction (B2287)
DESCRIPTION This DTC is stored when there is an open, short or ECU communication malfunction between the power management control ECU and certification ECU (smart key ECU assembly). DTC ...

Other materials about Toyota Venza:

Steering Lock Motor Drive Power Circuit
DESCRIPTION The steering lock ECU (steering lock actuator assembly) is connected to the power management control ECU. The steering lock ECU (steering lock actuator assembly) cannot activate the motor unless it receives permission signals from both ECUs. ...

Removal
REMOVAL PROCEDURE 1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL NOTICE: When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ). 3. REMOVE FR ...

Data List / Active Test
DATA LIST / ACTIVE TEST 1. DATA LIST HINT: Using the Techstream to read the Data List allows the values or states of switches, sensors, actuator and other items to be read without removing any parts. This non-intrusive inspection can be very useful beca ...

© 2016-2024 Copyright www.tovenza.com

0.1161