Toyota Venza: Skid Control ECU Communication Stop Mode

Toyota Venza Service Manual / Networking / Can Communication System / Skid Control ECU Communication Stop Mode

DESCRIPTION

Detection Item	Symptom	Trouble Area
Skid Control ECU Communication Stop Mode	"ABS/VSC/TRAC" is not displayed on "CAN Bus Check" screen of the Techstream. Applies to Skid Control ECU Communication Stop Mode in DTC Combination Table.	Power source circuit of skid control ECU Skid control ECU branch wire or connector Brake actuator (Skid control ECU)

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Turn the ignition switch off before measuring the resistances between CAN bus main wires and between CAN bus branch wires.
Turn the ignition switch off before inspecting CAN bus wires for a ground short.
After the ignition switch is turned off, check that the key reminder warning system and light reminder warning system are not operating.
Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If any doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.

PROCEDURE

1.	CHECK CAN BUS WIRE FOR DISCONNECTION (SKID CONTROL ECU BRANCH WIRE)

(a) Turn the ignition switch off.

(b) Disconnect the connector of the skid control ECU.

Text in Illustration

*1	Front view of wire harness connector (to Skid Control ECU)

Standard Resistance:

Tester Connection	Switch Condition	Specified Condition
A42-35 (CANH) - A42-14 (CANL)	Ignition switch off	54 to 69 Ω

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (SKID CONTROL ECU BRANCH WIRE)

2.	CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

(a) Turn the ignition switch to ON.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection	Switch Condition	Specified Condition
A42-28 (IG1) - Body ground	Ignition switch ON	11 to 14 V

Text in Illustration

*1	Front view of wire harness connector (to Skid Control ECU)

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.	CHECK HARNESS AND CONNECTOR (GROUND TERMINAL)

(a) Turn the ignition switch off.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
A42-4 (GND1) - Body ground	Always	Below 1 Ω

Text in Illustration

*1	Front view of wire harness connector (to Skid Control ECU)

REPLACE BRAKE ACTUATOR (SKID CONTROL ECU)

REPAIR OR REPLACE HARNESS OR CONNECTOR (GROUND CIRCUIT)

Air Conditioning Amplifier Communication Stop Mode

DESCRIPTION Detection Item Symptom Trouble Area Air Conditioning Amplifier Communication Stop Mode "Air Conditioner" ...

Power Steering ECU Communication Stop Mode

DESCRIPTION Detection Item Symptom Trouble Area Power Steering ECU Communication Stop Mode "EPS" is not displayed on ...

Other materials about Toyota Venza:

Transmitter ID1 Error (C2141/41-C2144/44)
DESCRIPTION The tire pressure warning valve and transmitter installed in each tire and wheel assembly measures the tire pressures. The measured values are transmitted as radio waves to the tire pressure warning antenna and receiver on the body and then se ...

Setting up the displays
Press the “SETUP” button while the vehicle is stopped. The “Custom Settings” screen is displayed on the multi-information display. If left idle for approximately 10 seconds, the display will revert to the previous screen. Select “Display / ...

Bottle holders
► For front seats ► For rear seats NOTICE - Items that should not be stowed in the bottle holders Put the cap on before stowing a bottle. Do not place open bottles in the bottle holders, or glasses and paper cups containing liquid. ...