Toyota Venza manuals

Toyota Venza: Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL) (P2769,P2770)

Toyota Venza Service Manual / U660e Automatic Transmission / Transaxle / Automatic Transaxle System / Short in Torque Converter Clutch Solenoid Circuit (Shift Solenoid Valve SL) (P2769,P2770)

DESCRIPTION

Shift solenoid valve SL is turned on and off by signals from the TCM to control the hydraulic pressure acting on the lock-up relay valve, which then controls operation of the lock-up clutch.

DTC No.

DTC Detection Condition

Trouble Area

P2769

TCM detects a short in the shift solenoid valve SL circuit when the shift solenoid valve SL is operated (2 trip detection logic).

  • Short in shift solenoid valve SL circuit
  • Shift solenoid valve SL
  • TCM

P2770

TCM detects an open in the shift solenoid valve SL circuit when the shift solenoid valve SL is not operated (2 trip detection logic).

  • Open in shift solenoid valve SL circuit
  • Shift solenoid valve SL
  • TCM

Fail-safe function:

If the TCM detects a malfunction, it turns shift solenoid valve SL off.

MONITOR DESCRIPTION

Based on the signals from the throttle position sensor, the air flow meter and the crankshaft position sensor, the TCM sends a signal to shift solenoid valve SL to regulate the hydraulic pressure and provide smoother torque converter engagement. Shift solenoid valve SL responds to commands from the TCM. The valve controls the lock-up relay valve to perform the torque-converter lock-up function. If the TCM detects an open or short circuit for shift solenoid valve SL, it will illuminate the MIL.

MONITOR STRATEGY

Related DTCs

P2769: Shift solenoid valve SL/Range check (Low resistance)

P2770: Shift solenoid valve SL/Range check (High resistance)

Required sensors/Components

Shift solenoid valve SL

Frequency of operation

Continuous

Duration

1 time

MIL operation

2 driving cycles

Sequence of operation

None

TYPICAL ENABLING CONDITIONS

P2769: Range check (Low resistance):

The monitor will run whenever the following DTCs are not present

None

Command to solenoid

ON

Time after command to solenoid OFF to ON

More than 0.008 sec.

P2770: Range check (High resistance):

The monitor will run whenever the following DTCs are not present

None

Command to solenoid

OFF

Time after command to solenoid ON to OFF

More than 0.008 sec.

TYPICAL MALFUNCTION THRESHOLDS

P2769: Range check (Low resistance):

Intelligent power MOS diagnosis fail signals detected while the solenoid is operated

Fail at solenoid resistance: 8 Ω or less

P2770: Range check (High resistance):

Intelligent power MOS diagnosis fail signals detected while the solenoid is not operated

Fail at solenoid resistance: 100 kΩ or more

COMPONENT OPERATING RANGE

Shift solenoid valve SL

Resistance: 11 to 15 Ω at 20°C (68°F)

WIRING DIAGRAM


CAUTION / NOTICE / HINT

NOTICE:

Perform the universal trip to clear permanent DTCs (See page ).


PROCEDURE

1.

INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL)

(a) Remove the TCM from the transaxle.


(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

6 (SL) - Body ground

20°C (68°F)

11 to 15 Ω


OK

REPLACE TCM


NG

2.

INSPECT SHIFT SOLENOID VALVE SL

(a) Remove shift solenoid valve SL.


(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Solenoid Connector (SL) - Solenoid Body (SL)

20°C (68°F)

11 to 15 Ω

Text in Illustration

*1

Shift Solenoid Valve SL


OK

REPLACE TRANSMISSION WIRE


NG

REPLACE SHIFT SOLENOID VALVE SL

Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART HINT: If a DTC is displayed during the DTC check, check the parts listed in the table below and proceed to the "See page" given. If multiple s ...

Pressure Control Solenoid "G" Performance (Shift Solenoid Valve SL4) (P2808)
DESCRIPTION The TCM uses the vehicle speed signal and signals from the transmission speed sensors (NC, NT) to detect the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear). Then the TCM compares th ...

Other materials about Toyota Venza:

Problem Symptoms Table
PROBLEM SYMPTOMS TABLE Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the tab ...

Diagnosis System
DIAGNOSIS SYSTEM 1. DESCRIPTION The main body ECU (driver side junction block assembly) and certification ECU (smart key ECU assembly) control the LIN communication system. LIN communication system data and Diagnostic Trouble Codes (DTCs) can be read thr ...

Installation
INSTALLATION CAUTION / NOTICE / HINT NOTICE: Always use a new grommet and valve core when installing the tire pressure warning valve and transmitter. Check that the washer and nut are not damaged, and replace them if necessary. Write ...

© 2016-2024 Copyright www.tovenza.com

0.1721