Toyota Venza: SFR Solenoid Circuit (C0226/21,C0236/22,C0246/23,C0256/24,C1225/25-C1228/28)

Toyota Venza Service Manual / Brake Control / Dynamic Control Systems / Vehicle Stability Control System / SFR Solenoid Circuit (C0226/21,C0236/22,C0246/23,C0256/24,C1225/25-C1228/28)

DESCRIPTION

These solenoids turn on when signals are received from the skid control ECU and they control the pressure acting on the wheel cylinders to control the braking force.

DTC Code	DTC Detection Condition	Trouble Area
C0226/21 C0236/22 C0246/23 C0256/24 C1225/25 C1226/26 C1227/27 C1228/28	Solenoid valve signal does not match the check result.	Solenoid circuit Brake actuator assembly (Solenoid)

DTC Code

DTC Detection Condition

Trouble Area

C0226/21

C0236/22

C0246/23

C0256/24

C1225/25

C1226/26

C1227/27

C1228/28

Solenoid valve signal does not match the check result.

Solenoid circuit
Brake actuator assembly (Solenoid)

WIRING DIAGRAM

PROCEDURE

1.	RECONFIRM DTC

HINT:

These codes are detected when a problem is determined in the brake actuator assembly.

The solenoid circuits are in the brake actuator assembly.

Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTC is output before replacing the brake actuator assembly.

(a) Clear the DTCs (See page ).

(b) Start the engine.

(d) Check if the same DTC is recorded (See page ).

Result	Proceed to
DTCs (C0226/21, C0236/22, C0246/23, C0256/24, C1225/25, C1226/26, C1227/27 and C1228/28) are not output	A
DTCs (C0226/21, C0236/22, C0246/23, C0256/24, C1225/25, C1226/26, C1227/27 and/or C1228/28) are output	B

HINT:

If a speed signal of 15 km/h (9 mph) or more is input to the skid control ECU, with the ignition switch ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.
If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.
If any DTCs are output while jiggling a connector or wire harness of the brake actuator assembly (skid control ECU), inspect and repair the connector or wire harness.
It is suspected that the DTCs were output due to a bad connection of the connector terminal.

CHECK FOR INTERMITTENT PROBLEMS

REPLACE BRAKE ACTUATOR ASSEMBLY

Open or Short Circuit in ABS Motor Relay Circuit (C0273/13)

DESCRIPTION The ABS motor relay supplies power to the ABS pump motor. While the ABS is activated, the ECU turns the motor relay on and operates the ABS pump motor. If the voltage supplied to the m ...

ABS Control System Malfunction (43)

DESCRIPTION This DTC is output when the VSC system detects a malfunction in the ABS control system. DTC Code DTC Detection Condition Trouble Area ...

Other materials about Toyota Venza:

Removal
REMOVAL PROCEDURE 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system. NOTICE: When disconnecting the cable, some systems ne ...

Installation
INSTALLATION PROCEDURE 1. INSTALL STEERING PAD (a) Check that the ignition switch is off. (b) Check that the cable is disconnected from the negative (-) battery terminal. CAUTION: Wait at least 90 seconds after disconnecting the cable from the negative ( ...

Removal
REMOVAL PROCEDURE 1. REMOVE REAR DOOR SCUFF PLATE 2. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP 3. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) 4. REMOVE DECK BOARD ASSEMBLY 5. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY 6. REMOVE DECK S ...