Components
COMPONENTS
ILLUSTRATION
Removal
REMOVAL
PROCEDURE
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).
2. REMOVE FRONT DOOR SCUFF PLATE LH
3. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
4. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
5. REMOVE ROOM TEMPERATURE SENSOR
(a) Disengage the 2 claws and remove the room temperature sensor. |
|
Inspection
INSPECTION
PROCEDURE
1. INSPECT ROOM TEMPERATURE SENSOR
(a) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
1 - 2 |
10°C (50°F) |
3.00 to 3.73 kΩ |
1 - 2 |
15°C (59°F) |
2.45 to 2.88 kΩ |
1 - 2 |
20°C (68°F) |
1.95 to 2.30 kΩ |
1 - 2 |
25°C (77°F) |
1.60 to 1.80 kΩ |
1 - 2 |
30°C (86°F) |
1.28 to 1.47 kΩ |
1 - 2 |
35°C (95°F) |
1.00 to 1.22 kΩ |
1 - 2 |
40°C (104°F) |
0.80 to 1.00 kΩ |
1 - 2 |
45°C (113°F) |
0.65 to 0.85 kΩ |
1 - 2 |
50°C (122°F) |
0.50 to 0.70 kΩ |
1 - 2 |
55°C (131°F) |
0.44 to 0.60 kΩ |
1 - 2 |
60°C (140°F) |
0.36 to 0.50 kΩ |
NOTICE:
HINT:
As the temperature increases, the resistance decreases (see the graph).
If the resistance is not as specified, replace the room temperature sensor.
Text in Illustration
*1 |
Component without harness connected (Room Temperature Sensor) |
*2 |
Sensing Portion |
Installation
INSTALLATION
PROCEDURE
1. INSTALL ROOM TEMPERATURE SENSOR
(a) Engage the 2 claws to install the room temperature sensor. |
|
2. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
3. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
4. INSTALL FRONT DOOR SCUFF PLATE LH
5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).
Fog light switch
The fog lights improve visibility in difficult driving conditions, such as
in rain or fog. The fog lights can be used when the headlights are on low beam.
Type A
1. Off
2. On
Type B
1. Off
2. On
Wiper intervals can be adjusted for intermittent ...
Reassembly
REASSEMBLY
PROCEDURE
1. INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING
(a) Using SST and a press, install a new front differential case rear
tapered roller bearing (inner race) to the front differential case.
SST: 09726-36010
...
Lubrication system
- Engine oil selection
“Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use Toyota approved
“Toyota Genuine Motor Oil” or equivalent to satisfy the following grade and viscosity.
Oil grade: ILSAC GF-5 multigrade engine oil
Recomm ...