ROAD TEST
1. PROBLEM SYMPTOM CONFIRMATION
(a) Inspect the SET function.
Text in Illustration
*1 |
ON/OFF |
*2 |
- SET |
(1) Turn the cruise control main switch on.
(2) Drive at the required speed of between 40 km/h (25 mph) and 200 km/h (125 mph).
(3) Push the cruise control main switch to - SET.
(4) Check that the SET indicator light illuminates at this time.
(5) After releasing the switch, check that the vehicle cruises at the set speed.
(b) Inspect the + function.
Text in Illustration
*1 |
ON/OFF |
*2 |
- SET |
*3 |
+ RES |
(1) Turn the cruise control main switch on.
(2) Drive at the required speed of between 40 km/h (25 mph) and 200 km/h (125 mph).
(3) Push the cruise control main switch to - SET.
(4) Check that vehicle speed increases while the cruise control main switch is pushed to + RES, and that the vehicle cruises at the newly set speed when the switch is released.
(5) Push the cruise control main switch to + RES and then release it immediately. Check that vehicle speed increases by approximately 1.6 km/h (1.0 mph) (tap-up control).
(c) Inspect the - function.
Text in Illustration
*1 |
ON/OFF |
*2 |
- SET |
(1) Turn the cruise control main switch on.
(2) Drive at the required speed of between 40 km/h (25 mph) and 200 km/h (125 mph).
(3) Push the cruise control main switch to - SET.
(4) Check that vehicle speed decreases while the cruise control main switch is pushed to - SET, and the vehicle cruises at the newly set speed when the switch is released.
(5) Push the cruise control main switch to - SET, and then release it immediately. Check that vehicle speed decreases by approximately 1.6 km/h (1.0 mph) (tap-down control).
(d) Inspect the CANCEL function.
Text in Illustration
*1 |
ON/OFF |
*2 |
- SET |
*3 |
CANCEL |
(1) Turn the cruise control main switch on.
(2) Drive at the required speed of between 40 km/h (25 mph) and 200 km/h (125 mph).
(3) Push the cruise control main switch to - SET.
(4) When performing any one of the following, check that the cruise control system is canceled and that the normal driving mode returns.
(e) Inspect the RES function.
Text in Illustration
*1 |
ON/OFF |
*2 |
- SET |
*3 |
+ RES |
(1) Turn the cruise control main switch on.
(2) Drive at the required speed of between 40 km/h (25 mph) and 200 km/h (125 mph).
(3) Push the cruise control main switch to - SET.
(4) Cancel cruise control operation by performing any of the above operations (other than turning the main switch off).
(5) After pushing the cruise control main switch to + RES at a speed of more than 40 km/h (25 mph), check that the vehicle resumes the speed set prior to the cancellation.
Fuel Tank Cap
Inspection
INSPECTION
PROCEDURE
1. INSPECT FUEL TANK CAP ASSEMBLY
(a) Visually check that the fuel tank cap assembly and gasket are not
deformed or damaged.
Text in Illustration
*a
Gasket
...
Terminals Of Ecu
TERMINALS OF ECU
1. CHECK TIRE PRESSURE WARNING ECU
HINT:
Inspect the connectors from the back side while the connectors are connected.
(a) Disconnect the L14 tire pressure warning antenna and receiver connector.
(b) Measure the voltage according to the ...
System Description
SYSTEM DESCRIPTION
1. OUTLINE OF THEFT DETERRENT SYSTEM
The theft deterrent system can be set by locking the doors using the
transmitter or key, or by opening and closing the doors (for details, refer
to Active Arming Mode or Passive Arming Mo ...