Toyota Venza: Removal

Toyota Venza Service Manual / U660e Automatic Transmission / Transaxle / Automatic Transaxle Assembly(when Not Using The Engine Support Bridge) / Removal

REMOVAL

CAUTION / NOTICE / HINT

NOTICE:

If automatic transaxle assembly parts are replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary (See page ).

PROCEDURE

1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

HINT:

See the steps from "Recover Refrigerant From Refrigeration System" through "Remove Engine Assembly with Transaxle" (See page ).

2. DISCONNECT FRONT CROSSMEMBER SUB-ASSEMBLY

3. REMOVE STARTER ASSEMBLY

4. REMOVE MANIFOLD STAY

5. REMOVE TCM

6. SEPARATE WIRE HARNESS

(a) Remove the 2 bolts and disconnect the 2 wire harnesses from the automatic transaxle assembly.

(b) Separate the park/neutral position switch assembly connector and 7 wire harness clamps from the automatic transaxle assembly.

7. REMOVE FLEXIBLE HOSE BRACKET SUB-ASSEMBLY

(a) Remove the bolt and flexible hose bracket sub-assembly from the camshaft housing sub-assembly LH.

(b) Remove the No. 1 breather plug (ATM) from the flexible hose bracket sub-assembly.

8. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY

(a) Remove the 11 bolts and automatic transaxle assembly from the engine assembly.

NOTICE:

To prevent damage to the 2 knock pins, do not pry between the automatic transaxle assembly and engine assembly.

9. REMOVE TORQUE CONVERTER ASSEMBLY

(a) Remove the torque converter assembly from the automatic transaxle assembly.

10. REMOVE FRONT ENGINE MOUNTING BRACKET

(a) Remove the 3 bolts and front engine mounting bracket from the automatic transaxle assembly.

11. REMOVE WIRE HARNESS CLAMP BRACKET

(a) Remove the 4 bolts and 4 wire harness clamp brackets from the automatic transaxle assembly.

12. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

(a) Remove the 2 bolts and No. 1 transmission control cable bracket from the automatic transaxle assembly.

13. REMOVE SPEEDOMETER DRIVEN HOLE (ATM) COVER SUB-ASSEMBLY

(a) Remove the bolt and speedometer driven hole (ATM) cover sub-assembly from the automatic transaxle assembly.

(b) Remove the O-ring from the speedometer driven hole (ATM) cover sub-assembly.

14. REMOVE NO. 1 OIL COOLER OUTLET HOSE

(a) Slide the clip and disconnect the No. 1 oil cooler outlet hose from the automatic transaxle assembly.

15. REMOVE NO. 1 OIL COOLER INLET HOSE

(a) Slide the clip and disconnect the No. 1 oil cooler inlet hose from the automatic transaxle assembly.

Components

COMPONENTS ILLUSTRATION ILLUSTRATION ILLUSTRATION ...

Installation

INSTALLATION PROCEDURE 1. INSPECT TORQUE CONVERTER ASSEMBLY 2. INSTALL TORQUE CONVERTER ASSEMBLY (a) Engage the splines of the input shaft and turbine runner. ...

Other materials about Toyota Venza:

Head restraints
Head restraints are provided for all seats. ► Front and rear outboard seats Vertical adjustment 1. Up Pull the head restraint up. 2. Down Push the head restraints down while pressing the lock release button. ► Rear center seat (fabric seat) ...

Open in Front Floor Electrical Key Oscillator Circuit (B27A5)
DESCRIPTION The certification ECU (smart key ECU assembly) generates a request signal and sends it to the indoor electrical key oscillator (for front floor). To detect the key inside the cabin, the indoor electrical key oscillator (for front floor) create ...

Data List / Active Test
DATA LIST / ACTIVE TEST HINT: Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermitt ...