REMOVAL
PROCEDURE
1. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
(See page )
2. REMOVE NO. 1 ANTENNA CORD SUB-ASSEMBLY
(a) Disengage the 7 clamps and remove the No. 1 antenna cord sub-assembly.
3. REMOVE ROOF HEADLINING ASSEMBLY
(See page )
4. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY (w/o Sliding Roof)
(a) Peel up the strips of tape so that the washer hose and No. 2 antenna cord sub-assembly can be removed.
Text in Illustration
Tape |
- |
- |
|
Front |
- |
- |
HINT:
Tape is not available as a supply part. Try to leave as much tape as possible on the roof headlining so that the tape can be reused.
(b) Remove the washer hose and No. 2 antenna cord sub-assembly from the roof headlining assembly.
5. REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY (w/ Sliding Roof)
(a) Peel up the strips of tape so that the washer hose and No. 2 antenna cord sub-assembly can be removed.
Text in Illustration
Tape |
- |
- |
|
Front |
- |
- |
HINT:
Tape is not available as a supply part. Try to leave as much tape as possible on the roof headlining so that the tape can be reused.
(b) Remove the washer hose and No. 2 antenna cord sub-assembly from the roof headlining assembly.
6. REMOVE UPPER BACK WINDOW PANEL TRIM
7. REMOVE BACK DOOR PANEL TRIM ASSEMBLY
8. REMOVE BACK DOOR TRIM COVER LH (w/o Power Back Door)
9. REMOVE BACK DOOR TRIM COVER LH (w/ Power Back Door)
10. REMOVE BACK DOOR TRIM COVER RH
11. REMOVE NO. 3 ANTENNA CORD SUB-ASSEMBLY
(a) w/o Satellite Radio:
(1) Disconnect the 2 connectors. |
|
(2) Disengage the 4 hooks and disconnect the washer hose.
(3) Disengage the 7 clamps.
Text in Illustration
*1 |
Clamp |
*2 |
Hook |
*3 |
Washer Hose |
- |
- |
(b) w/ Satellite Radio:
(1) Disconnect the connector. |
|
(2) Disengage the 4 hooks and disconnect the washer hose.
(3) Disengage the 5 clamps.
Text in Illustration
*1 |
Clamp |
*2 |
Hook |
*3 |
Washer Hose |
- |
- |
(c) Disconnect the connector and disengage the clamp. |
|
(d) Disengage the 4 clamps.
Text in Illustration
*1 |
Clamp |
*2 |
Grommet |
(e) Disconnect the grommet from the back door.
(f) Disengage the 2 claws.
(g) Remove the No. 3 antenna cord sub-assembly with the washer hose as shown in the illustration. |
|
Receiver Error (C2176/76)
DESCRIPTION
The signals are transmitted to the tire pressure warning antenna and receiver
on the body as radio waves and then sent to the tire pressure warning ECU.
DTC No.
DTC Detection Condition
Trouble Area
...
Removal
REMOVAL
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read Precaution thoroughly before servicing (See page
).
2. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD
3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after discon ...
Front Blower Motor
Components
COMPONENTS
ILLUSTRATION
Installation
INSTALLATION
PROCEDURE
1. INSTALL FRONT BLOWER MOTOR SUB-ASSEMBLY
(a) Install the front blower motor sub-assembly with the 3 screws.
(b) Con ...