Toyota Venza manuals

Toyota Venza: Removal

REMOVAL

CAUTION / NOTICE / HINT

HINT:

  • Use the same procedure for the RH side and LH side.
  • The procedure listed below is for the LH side.

PROCEDURE

1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing (See page ).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).


3. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)


4. REMOVE DECK BOARD ASSEMBLY


5. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY


6. REMOVE DECK SIDE TRIM BOX LH


7. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY


8. REMOVE DECK SIDE TRIM BOX RH


9. REMOVE NO. 1 DECK BOARD


10. REMOVE REAR SEAT SUB FLOOR PANEL ASSEMBLY


11. REMOVE REAR FLOOR FINISH PLATE


12. REMOVE RECLINING REMOTE CONTROL BEZEL


13. REMOVE LUGGAGE HOLD BELT STRIKER ASSEMBLY


14. REMOVE REAR DOOR SCUFF PLATE


15. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP


16. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY


17. REMOVE DECK TRIM SIDE PANEL ASSEMBLY


18. REMOVE REAR AIRBAG SENSOR

(a) Check that the ignition switch is off.

(b) Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Disconnect the connector from the rear airbag sensor.

NOTICE:

When disconnecting the airbag connector, take care not to damage the airbag wire harness.

(1) Push and hold the white housing lock, and slide the yellow outer connector locking sleeve.

Text in Illustration

*1

Housing Lock

*2

Outer Connector Locking Sleeve

(2) Push and hold the white housing lock again, and slide the yellow outer connector locking sleeve to disconnect the connector.

(d) Remove the nut and rear airbag sensor.

NOTICE:

Loosen the nut while holding the rear airbag sensor because the rear airbag sensor pin (stopper) is easily damaged.


Installation
INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The procedure listed below is for the LH side. PROCEDURE 1. INSTALL REAR AIRBAG SE ...

Seat Position Sensor
Components COMPONENTS ILLUSTRATION On-vehicle Inspection ON-VEHICLE INSPECTION CAUTION / NOTICE / HINT CAUTION: Be sure to follow the correct removal and installation procedures of the se ...

Other materials about Toyota Venza:

Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter
DESCRIPTION The stereo component amplifier assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function. HINT: A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter ...

Removal
REMOVAL PROCEDURE 1. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY (w/o Seat Heater System) 2. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY (w/ Seat Heater System) 3. REMOVE NO. 2 CONSOLE BOX CARPET 4. REMOVE CONSOLE BOX ASSEMBLY 5. REMOVE AIR CONDITION ...

Front Passenger Side Power Mirror cannot be Adjusted with Power Mirror Switch
SYSTEM DESCRIPTION When the mirror adjust switch is operated, the main body ECU (driver side junction block assembly) detects the switch operation and sends the mirror adjust switch signal to the outer mirror control ECU assembly (front passenger door) vi ...

© 2016-2022 Copyright www.tovenza.com

0.1397