Toyota Venza: Removal

Toyota Venza Service Manual / Sliding Roof / Convertible / Sliding Roof Housing / Removal

REMOVAL

PROCEDURE

1. REMOVE NO. 1 SLIDING ROOF GLASS SUB-ASSEMBLY

(a) Fully open the No. 2 sliding roof glass sub-assembly.

(b) Using a T20 "TORX" socket wrench, remove the 6 screws and No. 1 sliding roof glass sub-assembly.

2. REMOVE SLIDING ROOF SIDE GARNISH LH

(a) Using a T25 "TORX" socket wrench, remove the screw and sliding roof side garnish LH as shown in the illustration.

3. REMOVE SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedure for the RH side and the LH side.

4. REMOVE NO. 2 SLIDING ROOF GLASS SUB-ASSEMBLY

(a) Fully close the No. 2 sliding roof glass sub-assembly.

(b) Using a T25 "TORX" socket wrench, remove the 3 screws.

HINT:

Use the same procedure for the RH side and the LH side.

5. REMOVE ROOF HEADLINING ASSEMBLY

HINT:

Refer to the procedure up to Remove Roof Headlining Assembly (See page ).

6. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH

7. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:

Use the same procedure for the RH side and the LH side.

8. REMOVE NO. 3 SLIDING ROOF GLASS SUB-ASSEMBLY

(a) Remove the 20 nuts and No. 3 sliding roof glass sub-assembly.

9. REMOVE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY

(a) Remove the bolt, nut and room light bracket.

(b) Remove the bolt and sliding roof drive gear sub-assembly.

10. REMOVE FRONT SLIDING ROOF HOUSING MOUNTING BRACKET LH

(a) Remove the 2 bolts, 2 nuts and front sliding roof housing mounting bracket LH.

11. REMOVE FRONT SLIDING ROOF HOUSING MOUNTING BRACKET RH

HINT:

Use the same procedure for the RH side and the LH side.

12. REMOVE CENTER SLIDING ROOF HOUSING MOUNTING BRACKET LH

(a) Remove the 3 bolts, 3 nuts and center sliding roof housing mounting bracket LH.

13. REMOVE CENTER SLIDING ROOF HOUSING MOUNTING BRACKET RH

HINT:

Use the same procedure for the RH side and the LH side.

14. REMOVE REAR SLIDING ROOF HOUSING MOUNTING BRACKET LH

(a) Remove the bolt, nut and rear sliding roof housing mounting bracket LH.

15. REMOVE REAR SLIDING ROOF HOUSING MOUNTING BRACKET RH

HINT:

Use the same procedure for the RH side and the LH side.

16. REMOVE SLIDING ROOF HOUSING ASSEMBLY

(a) Remove the 18 nuts and sliding roof housing assembly.

NOTICE:

When removing the housing, be careful not to damage the vehicle.
Perform this step with 2 or more technicians.

Components

COMPONENTS ILLUSTRATION ILLUSTRATION ILLUSTRATION ILLUSTRATION ...

Disassembly

DISASSEMBLY PROCEDURE 1. REMOVE SLIDING ROOF HOUSING CENTER FRAME (a) Remove the 2 nuts and sliding roof housing center frame. 2. REMOVE N ...

Other materials about Toyota Venza:

Certification ECU Vehicle Information Reading/Writing Process Malfunction (B15F7)
DESCRIPTION This DTC is stored when items controlled by the certification ECU (smart key ECU assembly) cannot be customized via the navigation system vehicle customization screen. HINT: The certification ECU (smart key ECU assembly) controls the smart k ...

Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE STEERING RACK BOOT CLIP (for LH Side) (a) Using pliers, remove the steering rack boot clip. 2. REMOVE STEERING RACK BOOT CLIP (for RH Side) HINT: Perform the same procedure as for the LH side. 3. REMOVE NO. 2 STEERING RAC ...

Does not Play even after Bluetooth Audio Mode is Selected
CAUTION / NOTICE / HINT HINT: Even if the portable player can play audio content, it may not be able to play via the in-vehicle device. This does not necessarily indicate a malfunction of the in-vehicle device. PROCEDURE 1. CHECK ...