REMOVAL
PROCEDURE
1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (for 2GR-FE)
HINT:
Refer to the procedure up to Remove Engine Assembly with Transaxle (See page ).
2. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE (for 1AR-FE)
HINT:
Refer to the procedure up to Remove Engine Assembly with Transaxle (See page ).
3. REMOVE FRONT NO. 1 STABILIZER BRACKET LH
4. REMOVE FRONT NO. 1 STABILIZER BRACKET RH
HINT:
Perform the same procedure as for the LH side.
5. REMOVE FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY
6. REMOVE STEERING LINK ASSEMBLY
7. DISCONNECT FRONT FRAME ASSEMBLY (for 2GR-FE)
8. REMOVE FRONT ENGINE MOUNTING INSULATOR ASSEMBLY (for 2GR-FE)
9. REMOVE ENGINE MOUNTING INSULATOR LH (for 2GR-FE)
10. REMOVE ENGINE MOUNTING INSULATOR RH (for 2GR-FE)
11. REMOVE REAR ENGINE MOUNTING INSULATOR ASSEMBLY (for 2GR-FE)
12. REMOVE FRONT FRAME ASSEMBLY (for 1AR-FE)
13. REMOVE FRONT ENGINE MOUNTING INSULATOR ASSEMBLY (for 1AR-FE)
14. REMOVE ENGINE MOUNTING INSULATOR LH (for 1AR-FE)
15. REMOVE ENGINE MOUNTING INSULATOR RH (for 1AR-FE)
16. REMOVE REAR ENGINE MOUNTING INSULATOR ASSEMBLY (for 1AR-FE AWD)
17. REMOVE FRONT LOWER SUSPENSION ARM LH
18. REMOVE FRONT LOWER SUSPENSION ARM RH
HINT:
Perform the same procedure as for the LH side.
19. REMOVE FRONT SUSPENSION MEMBER DYNAMIC DAMPER (for 2WD)
(a) Remove the 2 bolts and front suspension member dynamic damper. |
|
20. REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER
21. REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER
22. REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION
(a) Install SST as shown in the illustration. Text in Illustration
SST: 09830-10010 09830-01010 09830-01040 09830-01050 SST: 09950-40011 09951-04020 09952-04010 09955-04011 |
|
(b) Using SST, remove the front suspension member body mounting front cushion. Text in Illustration
NOTICE:
|
|
23. REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH
(a) Install SST as shown in the illustration. SST: 09830-10010 09830-01010 09830-01040 09830-01050 SST: 09950-40011 09951-04020 09952-04010 09954-04010 09955-04011 Text in Illustration
|
|
(b) Using SST, remove the front suspension member body mounting rear cushion LH. Text in Illustration
SST: 09830-10010 09830-01010 09830-01040 09830-01050 SST: 09950-40011 09951-04020 09952-04010 09954-04010 09955-04011 NOTICE:
|
|
24. REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH
HINT:
Perform the same procedure as for the LH side.
Terminals Of Ecu
TERMINALS OF ECU
1. CHECK POWER MANAGEMENT CONTROL ECU
(a) Disconnect the D42 and D43 connectors.
(b) Measure the voltage and resistance according to the value(s) in the table
below.
Tester Connection
Wiring Color
Termi ...
Freeze Frame Data
FREEZE FRAME DATA
1. CHECK FREEZE FRAME DATA
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Navigation System / Trouble
Codes.
(e) Select a DTC to ...
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. CONNECT TECHSTREAM
(a) Connect the Techstream to the DLC3.
(b) Start the engine and run it at idle.
(c) Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.
HINT:
Refer to the Techstream operator's manu ...