Toyota Venza: Removal

Toyota Venza Service Manual / Steering Gear / Linkage / Steering Gear(for 1ar-fe 2wd) / Removal

REMOVAL

CAUTION / NOTICE / HINT

NOTICE:

When disconnecting the steering intermediate shaft assembly and pinion shaft of the steering gear assembly, be sure to place matchmarks before servicing.

PROCEDURE

1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

2. SECURE STEERING WHEEL

(a) Secure the steering wheel with the seat belt in order to prevent it from rotating.

HINT:

This operation is necessary to prevent damage to the spiral cable.

3. REMOVE FRONT WHEELS

4. REMOVE NO. 1 ENGINE UNDER COVER

5. REMOVE NO. 2 ENGINE UNDER COVER

6. SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

(a) Put matchmarks on the steering intermediate shaft assembly and steering link assembly.

Text in Illustration

Matchmark

(b) Remove the bolt and slide the steering intermediate shaft assembly.

7. SEPARATE TIE ROD ASSEMBLY LH

(a) Remove the cotter pin and nut.

(b) Install SST to the tie rod end.

SST: 09960-20010

09961-02060

NOTICE:

Make sure that the upper ends of the tie rod end and SST are aligned.

Text in Illustration

*1	Tie the string without allowing for any slack.	*2	Place the wrench here.
*3	Turn	-	-

SST: 09960-20010

09961-02010

CAUTION:

Apply grease to the threads and end of the SST bolt.

NOTICE:

When securing SST to the steering knuckle, be sure to tighten the string of SST to prevent it from falling.
Install SST so that A and B are parallel.
Be sure to place a wrench on the part indicated in the illustration.
Do not damage the front disc brake dust cover.
Do not damage the ball joint dust cover.
Do not damage the steering knuckle.

8. SEPARATE TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.

9. SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

10. SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.

11. REMOVE FRONT FLOOR BRACE

12. SEPARATE FRONT NO. 1 STABILIZER BRACKET LH

(a) Remove the 2 bolts and separate the front No. 1 stabilizer bracket LH.

13. SEPARATE FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.

14. SEPARATE FRONT STABILIZER BAR WITH BRACKET

(a) Separate the front stabilizer bar with bracket from the front frame assembly.

NOTICE:

Use wire or an equivalent tool to keep the front stabilizer bar with bracket.

15. REMOVE STEERING LINK ASSEMBLY

(a) Remove the 2 bolts, 2 nuts and steering link assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.

(b) Pull out the steering link assembly towards the left side of the vehicle while lifting the front stabilizer bar with bracket.

16. REMOVE TIE ROD ASSEMBLY LH

(a) Put matchmarks on the tie rod assembly LH and steering gear assembly.

Text in Illustration

Matchmark

(b) Loosen the lock nut, and remove the tie rod assembly LH and lock nut.

17. REMOVE TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.

Components

COMPONENTS ILLUSTRATION ILLUSTRATION ILLUSTRATION ILLUSTRATION ILLUSTRATION ILLUSTRATION ...

Disassembly

DISASSEMBLY PROCEDURE 1. REMOVE STEERING RACK BOOT CLIP (for LH Side) (a) Using pliers, remove the steering rack boot clip. 2. REMOVE STEERING RACK BOOT CLIP (for RH Side) HINT: Perform the same ...

Other materials about Toyota Venza:

Dtc Check / Clear
DTC CHECK / CLEAR 1. CHECK DTC (a) Connect the Techstream to the DLC3. (b) Turn the ignition switch to ON. (c) Turn the Techstream on. (d) Enter the following menus: Body Electrical / Smart Key. Main Body or Power Source Control / Trouble Codes. (e) Ch ...

Short in Front Passenger Side Squib 2nd Step Circuit (B1815/54-B1818/54)
DESCRIPTION The front passenger side squib 2nd step circuit consists of the center airbag sensor assembly and front passenger airbag assembly. The center airbag sensor assembly uses this circuit to deploy the airbag when deployment conditions are met. T ...

Winter driving tips
Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropriate to the prevailing weather conditions. - Pre-winter preparations • Use fluids that are appropriate to the p ...