REGISTRATION
CAUTION / NOTICE / HINT
HINT:
PROCEDURE
1. REGISTRATION OF RECOGNITION CODE (MANUAL OPERATION)
(a) The following conditions should be met.
(1) No key is inserted in the ignition key cylinder.
(2) Only driver side door is opened.
(b) Perform the following operations to select the desired mode.
(1) Insert and remove the key from the ignition switch twice within 5 seconds. (End in removed)
(2) After the above operation, close and open the driver door twice. (End in open)
Then insert the key into the ignition key cylinder and remove it.
HINT:
Complete this procedure within 40 seconds.
(3) After the above operations, close and open the driver door twice. (End in open)
Then insert the key into the ignition key cylinder and close the all door.
HINT:
Complete this procedure within 40 seconds.
(4) Turn the ignition switch from LOCK to ON and back to LOCK at approximately 1-second intervals 1 to 5 times to select a mode (see the illustration). Then remove the key from the ignition key cylinder.
HINT:
Complete this procedure within 40 seconds.
NOTICE:
If the number of the ON-LOCK operations of the ignition switch is 0, 4, 6 or more, there will be no response to inform which mode has been selected.
(5) After selecting a mode, the main body ECU (driver side junction block assembly) automatically performs the power door LOCK- UNLOCK operation within 5 seconds to inform the selected mode (see the illustration).
HINT:
(c) Register new recognition codes (Add mode or Rewrite mode):
(1) Within 45 seconds after add mode or rewrite mode has been selected, press the LOCK and UNLOCK switches on the transmitter switch simultaneously for 1.0 to 1.5 seconds.
Then, press either one of the switches for more than 1.0 second. (Procedure "A")
(2) Within 5 seconds after the transmitter switch has been released, the LOCK-UNLOCK operation will be automatically performed once if the registration of the recognition code of the transmitter is completed correctly.
If the LOCK-UNLOCK operation is performed twice, registration of the recognition code has failed. Perform the registration procedure from the beginning. (Procedure "B")
(3) If multiple transmitters need to be registered, repeat procedures "A" and "B" within 45 seconds each.
HINT:
2. REGISTRATION OF RECOGNITION CODE (USING TECHSTREAM)
(a) Turn the ignition switch to ON.
(b) Select either add or rewrite mode according to the Techstream display.
(c) The number of registered codes is indicated.
(d) Registration of the door control transmitter.
(1) If either add mode or rewrite mode has been selected, press the LOCK and UNLOCK switches on the transmitter simultaneously.
(2) Within 3 seconds of releasing the LOCK and UNLOCK switches, press either of the switches on the door control transmitter.
NOTICE:
(3) The main body ECU (driver side junction block assembly) automatically performs the power door LOCK-UNLOCK operation once in order to indicate whether registration has been completed correctly or not.
(4) If continuing registration, the next recognition code must be registered in the door control transmitter within 30 seconds.
HINT:
Up to 6 recognition codes can be registered.
(e) Completing the registration mode.
(1) Registration mode will end when any of the following occurs:
(f) Perform the following after registration is completed.
(1) Perform the wireless door lock control operation check (See page ).
HINT:
If the wireless door lock control does not operate, perform the registration procedure again.
Idle Control System Malfunction (P0505)
DESCRIPTION
The idle speed is controlled by the electronic throttle control system. The electronic
throttle control system is comprised of: 1) the one-valve-type throttle body; 2)
the throttle actuator, which operates the throttle valve; 3) the throttle p ...
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
HINT:
If a trouble code is output during the DTC check, inspect the trouble areas listed
for that code. For details of the code, refer to "See page" in the DTC chart.
Inspect the fuses and relays before troub ...
Installation
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.
PROCEDURE
1. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY
NOTICE:
The regulator arm mu ...