Toyota Venza: Reassembly
REASSEMBLY
PROCEDURE
1. INSTALL NO. 1 CENTER SUPPORT BEARING ASSEMBLY
|
(a) Set the No. 1 center support bearing on the intermediate shaft as shown in the illustration. NOTICE: Make sure to install the bearing in the correct position. |
|
(b) Install a new washer to the intermediate shaft.
|
(c) Align the matchmarks on the universal joint flange and intermediate shaft and place the flange on the shaft. Text in Illustration
|
|
.png)
|
(d) Using SST to hold the universal joint flange, press the No. 1 center support bearing assembly into position by tightening a new nut and washer. SST: 09330-00021 Torque: 182 N·m {1851 kgf·cm, 134 ft·lbf} Text in Illustration
|
|
(e) Loosen the nut.
(f) Tighten the nut again.
Torque:
69 N·m {701 kgf·cm, 51 ft·lbf}
|
(g) Using a chisel and a hammer, stake the nut. |
|
2. INSTALL NO. 2 CENTER SUPPORT BEARING ASSEMBLY
|
(a) Set the No. 2 center support bearing on the intermediate shaft as shown in the illustration. NOTICE: Make sure to install the bearing in the correct position. |
|
(b) Install a new washer to the intermediate shaft.
|
(c) Align the matchmarks on the universal joint flange and intermediate shaft, and place the flange on the shaft. Text in Illustration
|
|
.png)
|
(d) Using SST to hold the universal joint flange, press the No. 2 center support bearing assembly into position by tightening a new nut and washer. SST: 09330-00021 Torque: 182 N·m {1851 kgf·cm, 134 ft·lbf} Text in Illustration
|
|
(e) Loosen the nut.
(f) Tighten the nut again.
Torque:
69 N·m {701 kgf·cm, 51 ft·lbf}
|
(g) Using a chisel and a hammer, stake the nut. |
|
3. INSTALL INTERMEDIATE SHAFT
|
(a) Align the matchmarks on the intermediate shaft and rear propeller shaft, and then install 2 washers and 6 bolts. Text in Illustration
|
|
.png)
(b) Using a hexagon wrench (6 mm), tighten the 6 bolts with 2 washers temporarily.
4. INSTALL PROPELLER SHAFT
(a) Align the matchmarks on the propeller shaft and the universal joint flange.
|
(b) Install the propeller shaft to the front flange with the 4 bolts, 4 washers and 4 nuts. Torque: 74 N·m {750 kgf·cm, 55 ft·lbf} NOTICE:
|
|
.png)
(c) Check that each joint of the propeller with center bearing shaft assembly is facing the direction shown in the illustration.
Installation
INSTALLATION
PROCEDURE
1. TEMPORARILY TIGHTEN PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
(a) Remove SST from the transfer.
SST: 09325-20010
...
Propeller Shaft System
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of problem symptoms. If multiple
suspected areas are listed, the potential causes of the symp ...
Other materials about Toyota Venza:
Inspection
INSPECTION
PROCEDURE
1. INSPECT SPIRAL CABLE
(a) Visually check for defects with the spiral cable removed from the vehicle.
(1) The defects are as follows:
Scratches on the spiral cable
Small cracks the spiral cable
Dents on the spiral cabl ...
Reassembly
REASSEMBLY
PROCEDURE
1. INSTALL NO. 1 CENTER SUPPORT BEARING ASSEMBLY
(a) Set the No. 1 center support bearing on the intermediate shaft as
shown in the illustration.
NOTICE:
Make sure to install the bearing in the correct position.
...
Disassembly
DISASSEMBLY
PROCEDURE
1. INSPECT FRONT OIL PUMP AND GEAR BODY SUB-ASSEMBLY
2. REMOVE STATOR SHAFT ASSEMBLY
(a) Using a "TORX" wrench (T30), remove the 16 bolts and stator shaft
assembly from the oil pump body.
NOTICE:
Keep ...
0.1346