Toyota Venza: Reassembly

Toyota Venza Service Manual / Interior Panels / Trim / Roof Headlining / Reassembly

REASSEMBLY

PROCEDURE

1. INSTALL NO. 14 ROOF SILENCER PAD

(a) Align the markings on the roof headlining assembly with the No. 14 roof silencer pad and install the silencer pad using hot-melt glue as shown in the illustration.

2. INSTALL NO. 1 ROOF WIRE (w/o Sliding Roof)

(a) Install the No. 1 roof wire.

Text in Illustration

Adhesive Tape

(b) Turn the visor connectors clockwise approximately 90° to install the connectors to the roof headlining assembly.

HINT:

As shown in the illustration, line up and secure the reference tape of the wire harness to the tip of the roof headlining assembly.

3. INSTALL NO. 1 ROOF WIRE (w/ Sliding Roof)

(a) Install the No. 1 roof wire.

Text in Illustration

Adhesive Tape

(b) Turn the visor connectors clockwise approximately 90° to install the connectors to the roof headlining assembly.

HINT:

As shown in the illustration, line up and secure the reference tape of the wire harness to the tip of the roof headlining assembly.

4. INSTALL NO. 2 ROOF SILENCER PAD (w/o Sliding Roof)

(a) Align the markings on the roof headlining assembly with the 2 No. 2 roof silencer pads and install the silencer pad using hot-melt glue or double-sided tape as shown in the illustration.

5. INSTALL NO. 3 ROOF SILENCER PAD (w/o Sliding Roof)

(a) Align the markings on the roof headlining assembly with the 3 No. 3 roof silencer pads and install the silencer pad using hot-melt glue or double-sided tape as shown in the illustration.

6. INSTALL FRONT SIDE RAIL SPACER LH (w/o Sliding Roof)

(a) Align the markings on the roof headlining assembly with the roof side rail spacer LH and install the spacer using hot-melt glue as shown in the illustration.

7. INSTALL FRONT SIDE RAIL SPACER RH (w/o Sliding Roof)

HINT:

Use the same procedure for the RH side and the LH side.

8. INSTALL VANITY LIGHT ASSEMBLY

(a) Install the vanity light assembly (See page ).

HINT:

Use the same procedure for the RH side and the LH side.

9. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (w/o Sliding Roof)

10. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (w/ Sliding Roof)

Removal

REMOVAL PROCEDURE 1. REMOVE FRONT DOOR SCUFF PLATE LH (a) Disengage the 3 clips, 7 claws and guide, and remove the front door scuff plate LH. ...

Installation

INSTALLATION PROCEDURE 1. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof) (a) Pull the roof headlining assembly into the vehicle through the back door. NOTICE: Do not damag ...

Other materials about Toyota Venza:

Installation
INSTALLATION PROCEDURE 1. INSTALL FUEL PRESSURE PULSATION DAMPER ASSEMBLY (a) Apply a light coat of gasoline or spindle oil to a new O-ring. Text in Illustration *1 O-ring ...

Reassembly
REASSEMBLY PROCEDURE 1. INSTALL AIR OUTLET CONTROL SERVO MOTOR SUB-ASSEMBLY (a) Check that the slots, links and gears of the air outlet control servo motor sub-assembly are positioned in the correct orientation as shown in the illustratio ...

Speaker Output Short (B15C3)
DESCRIPTION This DTC is stored when a malfunction occurs in the speakers. DTC No. DTC Detection Condition Trouble Area B15C3 A short is detected in the speaker output circuit ...